1. The sensor substrate This is the silicon material, which measures the light intensity. The sensor is not actually flat, but has tiny cavities, like wells, that trap the incoming light and allow it to be measured. Each of these wells or cavities is a pixel. 2. A Bayer filter This is a colour filter that is bonded to the sensor substrate to allow colour to be recorded. The sensor on its own can only measure the number of light photons it collects. It has no way of determining the colour of those photons. As such, the sensor itself can only record in monochrome. The Bayer filter was derived by Dr. Bryce E. Bayer, a scientist working for Eastman's Kodak. He invented the particular Red, Green and Blue arrangement of colour filters to capture colour information. Because of the alternating Red/Green and Blue/Green arrangement, it is sometimes called an RGBG filter. The Bayer filter, often called the Colour Filter Array, or CFA, acts as a screen, only allowing light photons of a certain colour into each pixel on the sensor. If you look at the diagram of the Bayer pattern (left), you will see it is made up of alternating rows of Red/Green and Blue/Green filters. The red filters, for example, will only allow red light photons to pass into the pixel below it. Similarly, the green and blue filters, will only allow green and blue light, respectively, to pass into the pixels below. In this way, when the pixel measures the number of light photons it has captured, it knows that every photon is of a certain colour. For example, if a pixel that has a red filter above it has captured 5000 photons, it knows that they are all photons of red light, and it can therefore begin to calculate the brightness of red light at that point. A sensor is composed of millions of light sensitive areas or pixels. These can be thought of as a group of buckets, into which the light falls and is trapped. The number of light rays falling into each bucket determines the brightness level at each pixel. Once the bucket is full, the light level is said to be 'blown'. The buckets in the top image cannot measure the colour of the light, only the intensity. By placing a different coloured primary filter over each bucket, only light of that colour is captured. Each line of pixels has only two of the three primary colours, either red and green or blue and green. There is space between each light sensitive bucket on the sensor. This is where some of the on-chip electronics are located. Any light falling on this area would be wasted as it could not be recorded, but microlenses placed above the filter help direct light into one or other of the adjacent pixels.

Flossing is essential when it comes to excellent oral health long term. There is so much research to show that good flossing is linked with heart health, gut health and overall health. Many of our patients understand the importance of flossing but few of our patients actually do. The reason this is, is because manual flossing can be difficult and painful. This is why water flossing is so important as it is a gentler, easier way to floss between your teeth. Water flossing pushes all the debris, stuck between your teeth, out of your teeth and stimulates the gum tissue also.

Digital Image Sensors What is a megapixel? A megapixel is quite simply, one million pixels. The number of pixels on the sensor determines the megapixel value of a camera. Multiply the number of pixels wide by the number high to work out the total megapixels. A typical camera as images that are 3888 wide x 2592 high. This gives a total of 10,077,696 pixels or 10.07 megapixels. The reason you multiply this value by three to work out the megabyte size of a file is so that you take account of each of the three colour channels - red, green and blue. A single pixel, with only luminosity information and without any colour, is roughly 1 byte. If you now add the three colour channels to that, it becomes 3 bytes - 1 byte per colour channel. Digital Image Sensor Digital image sensors are the vital part of your digital camera. They are the light sensitive 'film' that records the image and allows you to take a picture. But how does it work, and what do all the names and numbers mean? A digital camera sensor is, in simple terms, made up of three different layers. 1. The sensor substrate This is the silicon material, which measures the light intensity. The sensor is not actually flat, but has tiny cavities, like wells, that trap the incoming light and allow it to be measured. Each of these wells or cavities is a pixel. 2. A Bayer filter This is a colour filter that is bonded to the sensor substrate to allow colour to be recorded. The sensor on its own can only measure the number of light photons it collects. It has no way of determining the colour of those photons. As such, the sensor itself can only record in monochrome. The Bayer filter was derived by Dr. Bryce E. Bayer, a scientist working for Eastman's Kodak. He invented the particular Red, Green and Blue arrangement of colour filters to capture colour information. Because of the alternating Red/Green and Blue/Green arrangement, it is sometimes called an RGBG filter. The Bayer filter, often called the Colour Filter Array, or CFA, acts as a screen, only allowing light photons of a certain colour into each pixel on the sensor. If you look at the diagram of the Bayer pattern (left), you will see it is made up of alternating rows of Red/Green and Blue/Green filters. The red filters, for example, will only allow red light photons to pass into the pixel below it. Similarly, the green and blue filters, will only allow green and blue light, respectively, to pass into the pixels below. In this way, when the pixel measures the number of light photons it has captured, it knows that every photon is of a certain colour. For example, if a pixel that has a red filter above it has captured 5000 photons, it knows that they are all photons of red light, and it can therefore begin to calculate the brightness of red light at that point. A sensor is composed of millions of light sensitive areas or pixels. These can be thought of as a group of buckets, into which the light falls and is trapped. The number of light rays falling into each bucket determines the brightness level at each pixel. Once the bucket is full, the light level is said to be 'blown'. The buckets in the top image cannot measure the colour of the light, only the intensity. By placing a different coloured primary filter over each bucket, only light of that colour is captured. Each line of pixels has only two of the three primary colours, either red and green or blue and green. There is space between each light sensitive bucket on the sensor. This is where some of the on-chip electronics are located. Any light falling on this area would be wasted as it could not be recorded, but microlenses placed above the filter help direct light into one or other of the adjacent pixels. 3. A microlens This tiny lens sits above the Bayer filter and helps each pixel capture as much light as possible. The pixels do not sit precisely next to each other-there is a tiny gap between them. Any light that falls into this gap is wasted light, and will not be used for the exposure. The microlens aims to eliminate this light waste by directing the light that falls between two pixels into one or other of them. Full colour If you've read everything so far very carefully, and had a good look at the picture of a Bayer pattern filter, you may have noticed that there are twice as many green squares as there are red or blue. This is because the human eye is much more sensitive to green light than either red or blue, and has a much greater resolving power in that range. Similarly, you may also have wondered how the full colour image is created, if each pixel can only record a single colour of light. Surely, each pixel is missing two thirds of the colour data needed to make a full colour image? Indeed it is, but due to some very clever algorithms within the camera, it succeeds in working out the full-colour for each pixel. The method used is called 'demosaicing', and is very complex. However, in simple terms, the camera treats each 2x2 set of pixels as a single unit. This provides one red, one blue and two green pixels, and the camera can then estimate the actual colour based on the photon levels in each of these four wells. Look at the diagram above. In that 2 x 2 square of four pixels, each pixel contains a single colour, either red, green or blue. Let's call them G1, B1, R1, G2. At the end of the exposure, when the shutter has closed and the pixels are full of photons, they start their calculations. If we take a single pixel, G1, this is what happens. G1 talks to B1, finds out how many blue photons it has got and adds them to its green. G1 then talks to R1 and G2 and does the same thing. G1 then has a complete set of primary colour data, from which it can build the full colour for its place on the sensor. At the same time as acquiring data from its neighbouring pixels, G1 is also giving its data to them so they can perform the same calculations. This is only half the story as it only considers a single pixel in a 2x2 grid. If you now image a pixel in the middle of a 3x3 grid, it can take the data from more pixels. Based on the standard Bayer pattern, if the pixel in the centre is green (above), the surrounding pixels will be made up of two blue pixels, two red pixels and four green pixels. If it is a red pixel in the centre (above), it will have four blue pixels and four green pixels around it. If it is a blue pixel in the centre (above), it will be surrounded by four green pixels and four red pixels. This still isn't the entire story, but exactly how cameras make up their full colour data is a closely guarded secret. You can assume that every single pixel is used by at least eight other pixels so that each can create a full panoply of colour data. Effective pixels What happens to the pixels right at the edge of a sensor? If they are the very edge pixel, they don't have as many surrounding pixels from which to borrow information, so their colour data is not quite as accurate. This is the difference between actual pixels and effective pixels. The actual number of pixels on a sensor is the total number of pixels. However, not all of these are used in forming the image. Those at the edge are ignored by the camera in forming the image, but their data is used by those further from the edge. This means that every pixel used in forming the image uses the same number of pixels to create its colour data. This is why, when reading camera specifications you might see 'effective pixels 10.1 million, total pixels 10.5 million. These extra 400,000 pixels in the total megapixels are the ones used to create colour data information, but are not used in forming part of the final image. The sensor in a camera has more pixels than are used to form the image. These extra pixels are used to improve the colour data in the image. Taken from an article from a Canon publication For more information, visit the website at www.canon.co.uk

Our Water Flosser with UV Steriliser’s main purpose is to clean between the teeth, the point at which two teeth meet. This is ideal for anyone who struggles with manual floss or anyone with braces, bad breath, restorative work like bridges crowns veneers and to stop staining build up between teeth.

Brand New High-quality LED Dimmable Photo Video Ring Light.Features: Adjustable brightness and colour temperature (3200K-5500K) to meet all your shooting ...

Full colour If you've read everything so far very carefully, and had a good look at the picture of a Bayer pattern filter, you may have noticed that there are twice as many green squares as there are red or blue. This is because the human eye is much more sensitive to green light than either red or blue, and has a much greater resolving power in that range. Similarly, you may also have wondered how the full colour image is created, if each pixel can only record a single colour of light. Surely, each pixel is missing two thirds of the colour data needed to make a full colour image? Indeed it is, but due to some very clever algorithms within the camera, it succeeds in working out the full-colour for each pixel. The method used is called 'demosaicing', and is very complex. However, in simple terms, the camera treats each 2x2 set of pixels as a single unit. This provides one red, one blue and two green pixels, and the camera can then estimate the actual colour based on the photon levels in each of these four wells. Look at the diagram above. In that 2 x 2 square of four pixels, each pixel contains a single colour, either red, green or blue. Let's call them G1, B1, R1, G2. At the end of the exposure, when the shutter has closed and the pixels are full of photons, they start their calculations. If we take a single pixel, G1, this is what happens. G1 talks to B1, finds out how many blue photons it has got and adds them to its green. G1 then talks to R1 and G2 and does the same thing. G1 then has a complete set of primary colour data, from which it can build the full colour for its place on the sensor. At the same time as acquiring data from its neighbouring pixels, G1 is also giving its data to them so they can perform the same calculations. This is only half the story as it only considers a single pixel in a 2x2 grid. If you now image a pixel in the middle of a 3x3 grid, it can take the data from more pixels. Based on the standard Bayer pattern, if the pixel in the centre is green (above), the surrounding pixels will be made up of two blue pixels, two red pixels and four green pixels. If it is a red pixel in the centre (above), it will have four blue pixels and four green pixels around it. If it is a blue pixel in the centre (above), it will be surrounded by four green pixels and four red pixels. This still isn't the entire story, but exactly how cameras make up their full colour data is a closely guarded secret. You can assume that every single pixel is used by at least eight other pixels so that each can create a full panoply of colour data. Effective pixels What happens to the pixels right at the edge of a sensor? If they are the very edge pixel, they don't have as many surrounding pixels from which to borrow information, so their colour data is not quite as accurate. This is the difference between actual pixels and effective pixels. The actual number of pixels on a sensor is the total number of pixels. However, not all of these are used in forming the image. Those at the edge are ignored by the camera in forming the image, but their data is used by those further from the edge. This means that every pixel used in forming the image uses the same number of pixels to create its colour data. This is why, when reading camera specifications you might see 'effective pixels 10.1 million, total pixels 10.5 million. These extra 400,000 pixels in the total megapixels are the ones used to create colour data information, but are not used in forming part of the final image. The sensor in a camera has more pixels than are used to form the image. These extra pixels are used to improve the colour data in the image. Taken from an article from a Canon publication For more information, visit the website at www.canon.co.uk

Spotlight uvlamp

Shop magnifying glasses for crafts and lighted magnifiers with stands and adjustable arms for your floor or table. Explore magnifying glasses for everyday ...

We are so happy to finally bring you our new Water Flosser with UV Steriliser that is sure to give you that “H2-Oh!” feeling in your life! Over the past 2 years we have listened to our customers to bring this new and improved Water Flosser to the market and we couldn't be happier with the finished product. The Water Flosser comes with a charger, replacement tips and user manual. Our UV Flosser is perfect for people with complex dental work including braces, implants and veneers. Our Water Flosser will help you maintain a white, bright smile and reduce any signs of bad breath….amazing we know and that's only some of the benefits.

Water flossing is an alternative for those patients who hate or find flossing difficult. Water flossing cleans in between the teeth, the point at which toothpaste and the toothbrush will not enter. Water flossing can be a gentler, more thorough cleaning option vs manual flossing.

The principal purpose of a polariser is to eliminate surface reflections, glare and hot spots from any light source entering the lens.

Get the best deal for Set Screws from the largest online selection at eBay.ca. | Browse our daily deals for even more savings!

Spotlight uvfor sale

3. A microlens This tiny lens sits above the Bayer filter and helps each pixel capture as much light as possible. The pixels do not sit precisely next to each other-there is a tiny gap between them. Any light that falls into this gap is wasted light, and will not be used for the exposure. The microlens aims to eliminate this light waste by directing the light that falls between two pixels into one or other of them.

Shopping from Great Britian? Please use our UK store for UK delivery. If you are shipping to the EU, stay on the EU store

SCHOTT consistently sets new standards for optical components, and prisms are a key area in which our products offer a clear USP. With a deep knowledge of glass ...

Home - Search - Suppliers - Links - New Products - Catalogues - Magazines Problem Page - Applications - How they work - Tech Tips - Training - Events -

Apr 8, 2021 — 50mm lenses don't zoom ... Like mentioned above, a 50mm lens is a single focal length prime lens. This means one thing about the focal length: it ...

Home - Search - Suppliers - Links - New Products - Catalogues - Magazines Problem Page - Applications - How they work - Tech Tips - Training - Events -

Spotlight uvresin

Each color of light has a different amount of energy. Molecules can only absorb light that matches the energy they need to move their electrons ...

Digital Image Sensors What is a megapixel? A megapixel is quite simply, one million pixels. The number of pixels on the sensor determines the megapixel value of a camera. Multiply the number of pixels wide by the number high to work out the total megapixels. A typical camera as images that are 3888 wide x 2592 high. This gives a total of 10,077,696 pixels or 10.07 megapixels. The reason you multiply this value by three to work out the megabyte size of a file is so that you take account of each of the three colour channels - red, green and blue. A single pixel, with only luminosity information and without any colour, is roughly 1 byte. If you now add the three colour channels to that, it becomes 3 bytes - 1 byte per colour channel. Digital Image Sensor Digital image sensors are the vital part of your digital camera. They are the light sensitive 'film' that records the image and allows you to take a picture. But how does it work, and what do all the names and numbers mean? A digital camera sensor is, in simple terms, made up of three different layers.

Sep 9, 2020 — By moving its knob you will be able to control the amount of light passing through your specimen. While working with nonliving material stained- ...

... polarizers, polarizing beamsplitting cubes and plates, wire grid polarizers, beam displacers, and depolarizers. Our polarizer lineup is constantly expanding ...

We can't wait to see what you all think of our newest addition to the Spotlight Oral Care family, if you try it be sure to tag us on Instagram @spotlight_oral_care and let us know what you think!

Jul 24, 2024 — LUCID Vision Labs added a dual extended-head camera to its Phoenix GigE PoE camera family and secured a 2024 VSD Innovators Award for ...