The days of the Electroluminescent (EL), Cold Cathode Fluorescent Lamp (CCFL) and front lights, are over for LCD displays. The large TV application was the last to employ a CCFL, but now with the lower cost and improved light quality of LEDs even TV’s have adopted the edge lit LEDs.

Diffusing light for a photoshoot can make your subjects look softer and minimize blemishes. If you don't have access to professional equipment and you need to improvise, you have a few different options, like wrapping 1 or 2 layers of bubble wrap around your camera's flash, aiming your light source at a semi-reflective white surface like a wall or poster board, or hanging a light-colored sheer fabric between your subject and the light source. You could even hang up white Chinese paper lanterns from the ceiling to help diffuse the lighting in your shot. There are also professional-level diffusers you can use if you're willing to spend more, like an on-camera flash diffuser, a softbox, or a photography umbrella. For more suggestions, like how to use diffusion paper to diffuse light, keep reading! Did this summary help you?YesNo

Did You Know? Flat, diffused light is great for family, newborn, and maternity photography, because it creates a soft look. However, unfiltered light will create drama and emotion in your photos—there's no right or wrong, so experiment with both.

CCS inc

The advantages of an LED array are the low cost and high uniformity. With the downsides of an LED array backlight system being typically limited to yellow-green spectrum due to LED chip costs and the additional thickness required to house the light array.

LED arrays are often used on the smaller low-information content displays, such as character displays and simple monochrome icon-based TN display types.They’re typically used in the yellow-green color range because this provides the maximum light output at the lowest cost.

When it comes to LCD displays, one of the most critical components of any design is the LCD backlight system. The backlight enables transflective displays to be visible in low-light situations and enables transmissive displays to be visible, period.

Advanced illumination

LED array backlight designs involve an array of backlight LED chips that are soldered directly to a PCB board and then epoxy encapsulated. The chip form LEDs shine directly toward the LCD display and through a diffuser on the front surface of the backlight to evenly distribute this direct light.

High-bright white LEDs are used to further maximize brightness and the final surface of this backlight system is a diffuser to evenly distribute the light into the LCD glass.

This article was co-authored by Vlad Horol and by wikiHow staff writer, Amber Crain. Vlad Horol is a Professional Photographer and the Co-Founder of Yofi Photography, his portrait photography studio based in Chicago, Illinois. He and his wife Rachel specialize in capturing maternity, newborn, and family photos. He has been practicing photography full-time for over five years. His work has been featured in VoyageChicago and Hello Dear Photographer. This article has been viewed 197,948 times.

If you are using any type of backlight display, your options will be most likely one of these listed, and may still vary depending on your exact design needs.

Unlike LED arrays, edge lit backlight designs align the LED’s to the side(s) of the backlight system. These LEDs fire light along the side into the light-guide instead of directly up like the LED Array. This light travels through the light guide and is evenly distributed light throughout the entire display surface by employing a specially designed and varying texture pattern. This texture on both the front and back surface of the light-guide create small dimples which act to scatter and evenly distribute the light out of the face of the light guide. Larger dimples, or a higher density of dimples, will scatter more light out of the display. The texture pattern will be lighter closest to the LEDs whereas the light intensity is higher and much heavier as you move farther away from the LED. This accomplishes a uniform backlight system where the entire surface is the same luminance independent of the actual distance from the LED light source.

Uniformlight meaning

Topics: Color Displays, Customization, Monochrome Displays

The combination of the enhancement films, separate light guide and frame, high bright LEDs, and specialty films are necessary to provide the 150 to 1,000 nits of brightness required at the surface of the color LCD display in order to be to be visible and vibrant.

For color display applications, a whole new set of obstacles require a unique backlighting solution. Color filters for color displays block out two-thirds of all light, which means color displays require far brighter backlights to be effective. Additionally the range of color depth requires a much higher luminance to clearly distinguish the color grey shades to result in a vibrant color image to the end user. And when an LCD is competing with outdoor sunlit environments, this luminance requirement is even higher.

The design of edge lit backlights for color applications is similar to mono displays with the edge concept, but they use a separate light guide insert and light box to more efficiently contain and reflect light. Additionally, these systems use a high efficiency reflector and a crossed combination of two brightness enhancement films which act to redirect the light so it is focused more perpendicular to the LCD display and increase the intensity or brightness at the user. It requires two films, one in the X direction and one in the Y direction to focus the entire cone of light.

Diffusing light means to soften it by reducing glare and harsh shadows. In diffused lighting, subjects will appear to have shadows with very soft edges or no edges at all. Diffused light can bring out the best in your photography subjects by minimizing blemishes and wrinkles. It can also be used to create a very soft, cinematic look. There are a number of ways to diffuse light. You can purchase professional photography equipment to soften light, but there are many ways you can improvise, using objects you already have around, to get a similar effects.

The advantages of the edge lit mono style are its thinner design and fewer LEDs, which require less power and can lower costs when dealing with more expensive white, blue, or red multichip LEDs. The edge lit backlight can also be a versatile mechanical component and can incorporate display mounting features directly into the backlight. The LED edge lit (mono) design is the lowest-cost and preferred solution for mono graphic LCD displays.