PVC glovesvs nitrile

* Wind barrier boards must be covered with cladding as soon as possible. In order to guarantee the conversion of humidity, a 20–50 mm air gap must be left between the board and the cladding. The battens of the cladding must be vertical or constructed in a way that guarantees the vertical movement of the air between the cladding and the wind barrier board.

CA Residents WARNING: This product can expose you to chemicals, including DEHP, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

PVC glovesmeaning

Installation of 12 mm wind barrier boardsUse hot-dip galvanized nails with large nail heads (length: 40 mm or longer) or staples (length: 32 mm). The distance between nails/staples and the edge of the board must be at least 10 mm. The distance between these nails/staples that are attached to the edge of the board must be 100 mm; the distance between these nails/staples that are attached to the centre of the board must be 200 mm.

PVC glovesprice

Wind barrier boards must be installed in a way that there are 2–3 mm gaps left between the boards. To ensure the weather ability of these connections that are not on the frame, a wooden joist must be set under the connection site and the ends of the boards are attached to this joist. You can also use elastic construction tape to tighten the 25 mm boards.The boards are attached with either nails or staples.A longitudinal streak in a centre of a board simplifies the nailing of the board.

J. J. Keller protects people and the businesses they run. You can trust our expertise across a wide range of subjects relating to labor, transportation, environmental, and worker safety. Our deep knowledge of federal and state agencies is built on a strong foundation of more than 100 editors and consultants and 70+ years of regulatory compliance experience.

Nordic Fibreboard does not assume any responsibility or liability for any specific construction, assembly solutions, drawings and work processes, which are shown on any Nordic Fibreboard marketing material. All the information about product use are for guidance and illustration purposes only. Nordic Fibreboard does not assume any responsibilty of any decision made by arhitects or constructors. The full responsibilty of any construction should perform by arhitects and constructors.

PVC GlovesGreen

PVC GlovesDisposable

Wind barrier boards are used as a wind blocking, insulating and stiffening elements in constructions of exterior walls, ceilings and roofs.

Installation of 25 mm wind barrier boardsUse hot-dip galvanized nails, we recommend nails with large nail heads (length: 70 mm or longer) or staples (length: 58 mm or longer). The distance between nails/staples and the edge of the board must be at least 10 mm. The distance between these nails/staples that are attached to the edge of the board must be 100–150 mm; the distance between these nails/staples that are attached to the centre of the board must be 300 mm.

J. J. Keller protects people and the businesses they run. You can trust our expertise across a wide range of subjects relating to labor, transportation, environmental, and worker safety. Our deep knowledge of federal and state agencies is built on a strong foundation of more than 100 editors and consultants and 70+ years of regulatory compliance experience.

Installation of 25 mm wind barrier boars with tongue and groove joints (UNIVERSAL boards)Unlike the usual wind barrier boards, the wind barrier boards with joints are attached horizontally (perpendicularly to frame). This eliminates the possibility that the connections of the boards do not overlap with the frame (no need to install additional joists, no need to use construction tape etc). This prevents the cold bridges from forming (if possible, install the boards so that they are slightly shifted).Use hot-dip galvanized nails to attach the boards, we recommend nails with large nail heads (length: 70 mm or longer) or staples (length: 58 mm or longer). In order to prevent damages to joints, the distance between nails/staples and the edge of the board must be at least 35 mm. The distance between these nails/staples that are attached to the edge of the board must be 100–150 mm; the distance between these nails/staples that are attached to the centre of the board must be up to 200 mm.

Wind barrier boards are attached to construction in direction of frame. Distance between frame beams (measured from the centre-to-centre of the beam) must be 600 mm.