Vn filter

201881 — Ein Faden ist stringent. Kohärenz beschreibt eher ein Netz bei dem mehrere Punkte über mehrere Knoten verbunden sind, oder eine Baum- oder ...

The LRGB filter set is designed for maximum contrast and with extremely high gradients for clear differentiation of colours. The LRGB filter set divides the spectrum into its components red, green, blue and luminance.

Long passfilters

If you measured correctly and gSender told you to let it change the values and it set it to the numbers you gave then I’m wondering if it’s a bug, you’d have to measure pretty poorly to be of by ~50%.

Our currency rankings show that the most popular Canadian Dollar exchange rate is the CAD to USD rate. The currency code for Canadian Dollars is CAD. The ...

Jan 30, 2024 — More generally, light that is reflected off a surface at just the right angle will be polarized parallel to that surface. It also happens that ...

DielectricFilters

Jul 4, 2021 — The key difference between depth of focus and depth of field is that the former refers to the range of focus behind the camera lens. Depth of ...

Can somebody chime in and tell me what is going on, I surfaced my spoil board last night which turned out amazing. I would like to carve grid lines in it but until I can get confirmation that everything is good I will not proceed. IMG_01303264×2448 1.27 MB

Absorptivefilters

Lensimaging

OIII emission overlaps on blue and green filters with maximum transmission to allow high efficiency and natural colour imaging. Gap between green and red filters serves to block out the primary Sodium light pollution line at 589nm and improves colour balance and separation.

TECHSPEC Knife-Edge Pickoff Mirrors consist of three metallic coating options, fused silica substrates, and sharp 45-degree bevel.

IMPORTANT: Filters manufactured by Optolong are NOT designed for observing or photographing the Sun. DO NOT use Optolong filters to observe or photograph the Sun. If you do it will result in permanent eye damage!

(305 mm/min.) To glass and lens bonding adhesives. 3M™ Optically Clear Adhesive. Products. 8146-1.

UV Window Film is a protection against the fading effects of UV rays on your furnishings. UV Blocking Window Film stops 99% of harmful UV rays.

Edgefilters

The Major Emission Lines of Artificial Light Pollution: Hg / Mercury (435.8nm, 546.1nm, 577nm and 578.1nm), Na / Sodium (598nm, 589.6nm, 615.4nm and 616.1nm)

Quick update, the Firmware settting 100 was @ 297 which explains the X travel. The Y setting 101 was @ 197. I reset them both back to the default value 200 step/mm and everything is working as far as travel goes. Now I need to create my grid lines on the spoil board.

Apr 26, 2021 — Light can be polarised by passing it through a polarising filter. A polarising filter has all its molecules aligned in the same direction. As a ...

MidwestFilters

toolant Allen Wrenches Sets, Unique Patented Holder Design for Magnetizing and Demagnetizing · Color coding for size identify easily · Magnetic system avoids ...

Simple, Inexpensive, Fast |By Single or By Pack of 2 | For Creating Prismatic And Spherical corrections | Applied To The Entire Lens Or To Any Region Of The ...

My X axis does not seem to travel the width of the machine, I have a 30x30 MKII and when I travel with X roughly a half inch away from full stop I only get 22.226 width. My Y travel is 33.480 which seems normal? Z is also roughly a 1/2 inch from stop.

Not sure I understand your problem. Are you saying that the machine travels the whole way from left to right and only reads ~22" or that it only moves ~22"?

EDIT: You said you did the calibration test, did you have to change any of the steps per mm? They are firmware settings $100 - $102 and they all default to 200 and if they are changed I would expect them to still be pretty close to 200.

@_Michael Yes, the machine travel shows roughly 22" as shown in the attachment. I did have to change the steps during the calibration test, I thought this was necessary since it was shown in the calibration process.

Do you have the inductive sensors? If you do you should have homing enabled as well as hard and soft limits. The soft limits require the machine dimensions to be set correctly in the firmware $130 - $132. Just throwing that out there just in case even though you didn’t mention any alarms or errors. That’s another question, are there any errors or alarms?

Colorfilters

From your post after the one with this quote I take it you found the firmware settings in gSender. You can also view them in the console by entering $$ and change them by typing $[setting number]=[value], brackets used to indicate a paceholder and not in command, but the settings in gSender are easier to get started with. If you ever need to check default values you can find them in the LongMill MK2 resources here. The ones that say [mask] are a bit mask, a combination of values, and require a table to find out what values do what. Those tables as well as info about what each setting does can be found here on the GRBL Wiki.

As the OP has resolved his issue, I am closing this thread. Thank you, guys, for pointing @GettingStarted in the right direction.