We have addressed the photonic generation of mmW signals using two approaches enabled by the use of QD laser technology:

To create a high purity mmW carrier, the two optical signals used to generate the beat signal should have the same intensity and a well-defined phase relationship. These characteristics are found in a mode-locked laser such as the QD device described in the section on coherent communications, above. Because the laser is mode-locked, there is a well-defined phase relationship between the different lasing lines, which means the beating of any two individual lines produces a pure tone with a linewidth of the order of only 5 kHz. By choosing an appropriate pair of lines a mmW beat signal can be generated from tens of GHz to THz. This scheme can be used to generate the optical source for a mmWoF networkFootnote 7 where one or both of the laser lines are modulated to carry the data. We have demonstrated a 16 Gb/s radio-over-fibre–based optical heterodyne RF wireless signal delivery at 25 GHz with a total of 25 km of fibre link and a 2-metre wireless link.Footnote 7 Footnote 8

The line graph for 230 gigahertz mode spacing shows the intensity of light that a laser emits as a function of wavelength at 400 milliampere drive current. The x-axis is labelled "wavelength (nm)" and the y-axis is labelled "intensity (dBm)".

Quantum laserfor sale

Using the dual wavelength QD laser with a 47-GHz mode spacing, we demonstrated real-time broadband multi-Gb/s mmW signal generation and wireless transmission at the frequency band of 47 GHz based on analog radio-over-fibre (AroF) fronthaul. One laser mode was encoded using 6-Gbaud multi-level quadrature amplitude modulation (M-QAM) (16-/32-/64-QAM) baseband data signals; the other lasing mode was used as an optical local oscillator for optical-heterodyne remote up-conversion to a mmW carrier of 47.2 GHz. Consequently, optical baseband modulated data signals with data capacity up to 36 Gb/s (6-Gbaud × 64-QAM) were transmitted through back-to-back (B2B) and 50 km of standard single-mode fibre (SSMF) before the mmW carrier was optically synthesized remotely for free space wireless data transmission and detection over a 9-metre air gap.Footnote 9

QuantumcascadelaserPDF

The demand for high-speed data communications continues to grow, requiring the development of more complex modulation schemes for higher speed and spectral efficiency while reducing costs. This puts high demands on the optical sources used to generate and carry the signals. The use of high spectral efficiency advanced coherent modulation schemes, such as multiple order quadrature amplitude modulation (QAM) for multiple simultaneous wavelength channels or the creation of a superchannel, requires many lasing wavelengths. Each wavelength channel must demonstrate both low relative intensity noise (RIN) and narrow linewidth (low phase noise). Combining multiple individual lasers becomes impractical for large channel counts and is infeasible when a fixed-mode spacing and a well-defined phase relationship are required between the lasing lines. A preferred approach is to use laser frequency combs to provide a source of evenly spaced narrow lasing lines with well-defined phase relationships between the lines. Conventional frequency comb sources, however, are typically complex to control, bulky, power hungry and expensive, making their deployment unattractive. The use of QD lasers can solve these issues.

She is referenced in books such as Ken Croswell's Magnificent Mars (2003)[11] and Tetsuya Tokano's Water on Mars and Life (2004).[12] She was the subject of a major profile in the New York Times Sunday Magazine (March 22, 2018) by Helen Macdonald, "In Her Orbit: Nathalie Cabrol Searches the Earth for the Secrets of Life on Mars," which documented her high-altitude explorations in the Andes.[13] This profile is also included in Helen Macdonald's collection of essays, Vesper Flights (2020).[14]

Renaudier, J., Brenot, R., Dagens, B., Lelarge, F., Rousseau, B., Poingt, F., Legouezigou, O., Pommereau, F., Accard, A., Gallion, P., et al. "Phase correlation between longitudinal modes in semiconductor self-pulsating DBR lasers." Electron. Lett. 41, (2005) 1007–1008. https://doi.org/10.1109/LPT.2005.843977.

A graph showing a typical lasing spectrum for a quantum dot laser has many thin vertical lines, each representing the intensity of light at different laser wavelengths. The x-axis is labelled "line wavelength (nm)" and the y-axis is labelled "optical power (dBm)".

Rahim, M., et al. "Monolithic InAs/InP quantum dash dual-wavelength DFB laser with ultra-low noise common cavity modes for millimeter-wave applications." Opt. Express 27(24), (2019): 35368–35375. https://doi.org/10.1364/OE.27.035368.

The units on the x-axis (line wavelength) go from 1540 nanometres at the origin to 1560 nanometres. The units on the y-axis (optical power) go from -70 decibel-milliwatts at the origin to +10 decibel-milliwatts. The 3-decibel bandwidth of the laser is 9.3 nanometres, from 1545.8 nanometres to 1555.2 nanometres, at a central wavelength of 1550.5 nanometres with 42 lasing modes. The 10-decibel bandwidth is 12.5 nanometres, from 1543.3 nanometres to 1555.8 nanometres, at a central wavelength of 1549.6 nanometres with 56 lasing modes.

The semiconductor laser is the workhorse of the telecommunications and data communications industry, used as the light source for transmitting data over optical fibre. These lasers have been traditionally based on indium phosphide (InP) materials, and in particular use quantum wells (QWs) as the gain medium. In 1982, predictions were made of improved performance for quantum dot-based lasers over their QW counterparts,Footnote 1 with promises of lower thresholds, temperature dependence and back-reflection sensitivity. This led to long-term studies looking at how to create such quantum dot (QD) structures, how to implement them in lasers and the comparison of their performance relative to QW lasers.

The dual-wavelength laser is an InP-based p-n blocked buried-heterostructure distributed feedback (BH DFB) structure using QD gain material. A novel synthesized aperiodic diffraction grating layer was designed to provide the distributed feedback such that two longitudinal modes would lase simultaneously. Particular attention was paid to obtaining almost identical threshold gain for both desired modes. Examples of lasing spectra are shown in figure 3, which demonstrates two different wavelength separations, 47 GHz and 230 GHz.

She is the principal investigator of the SETI Institute NAI team, which was selected in October 2014 to develop new biosignature detection and exploration strategies in support of the then-upcoming Mars 2020 mission. She was appointed in August 2015 to head the SETI Institute's Carl Sagan Center for the Study of Life in the Universe.

Quantum lasertherapy

Cabrol was the science principal investigator (PI) of the NASA Nomad rover field experiment (1997), and other NASA ASTEP-funded science and technology projects including Life in the Atacama (2003–2006) and Subsurface Life in the Atacama (2011–2015). She is the PI of the NASA ASTEP Planetary Lake Lander project (2011–2015) that explores the impact of ice loss on planetary lakes using technology developed for the exploration of Titan.

An exploded-view drawing shows the assembly relationship of the parts of an optical design, with the parts identified by labels. The assembly locks the output of a quantum dot laser to a fixed wavelength grid.

Quantum laserhair removal

Liu, G., et al. "Monolithic InAs/InP quantum dash mode-locked lasers for millimeter-wave-over-fiber mobile fronthaul systems." IEEE J. Sel. Top. Quantum Electron. 29(6), (2023):1900110. https://doi.org/10.1109/JSTQE.2023.3273539.

The InAs quantum dots are grown using a self-assembled Stranski–Krastanov growth process that has been optimized to allow precise control of the emission wavelength of each QD layer and minimize the broadening.Footnote 2 The physically discrete nature of each QD emitter creates an inhomogeneously broadened gain material that reduces the interaction between individual QDs through the charge carrier distribution. For certain applications, this property has demonstrated laser performance that is superior to that demonstrated with QW gain materials. These applications include high-speed data communications (including coherent modulation schemes) and radio over fibre (RoF).

Figure 2 shows the schematic and actual implementation of a mode-locked QD laser that has been locked to a fixed 25 GHz frequency grid.

The units on the x-axis (wavelength) go from 1538 nanometres at the origin to 1541 nanometres. The units on the y-axis (intensity) go from -70 at the origin to 0. The 60-milliampere drive current line peaks twice, at 1538.7 nanometres (-52 decibels) and at 1539.5 nanometres (-52 decibels). The 200-milliampere drive current line peaks 4 times, at 1538.9 nanometres (-38 decibels), at 1539.3 nanometres (1 decibel), at 1539.7 nanometres (1 decibel), and at 1540.0 nanometres (-37 decibels).

The units on the x-axis (wavelength) go from 1538 nanometres at the origin to 1545 nanometres. The units on the x-axis (wavelength) go from 1538 nanometres at the origin to 1545 nanometres. The units on the y-axis (intensity) go from -70 decibels at the origin to 0 decibels.

Poole, P. J., Kaminska, K., Barrios, P., Lu, Z., and Liu, J. "Growth of InAs/InP-based quantum dots for 1.55 µm laser applications." J. Cryst. Growth 311, (2009) 1482–1486. https://doi.org/10.1016/j.jcrysgro.2009.01.129.

The NRC's patent and process IP portfolio of QD technologies demonstrates the NRC's ability to innovate and enable best-in-class and disruptive technologies. The CPFC has been fabricating QD-based lasers at 1550 nm commercially for over a decade.

QuantumCascadelaserprice

Schematic of an optical design for a fibre coupled quantum dot laser assembly for locking the laser output to a fixed wavelength grid.

Operation of the laser creates many lasing lines, e.g. 56 at a 28.4 GHz mode spacing, as shown in panel (c) of figure 2. Each of these lasing lines has verified low RIN and low linewidth,Footnote 4 making them ideal for data communication over optical fibre at wavelengths around 1.55 µm. We have demonstrated data rates up to 22 Gb/s for an individual line using dual polarization 16-QAM at a base modulation rate of 28 GHz. This provides an aggregate data rate of 12.5 Tb/s for the whole lasing spectrumFootnote 5 and has been demonstrated for both for back-to-back (B2B) and over 100 km of standard single-mode fibre (SSMF). This finding highlights the viability for the QD lasers as a low-cost optical source for large-scale networks.Footnote 5 Footnote 6

Zeb, K., et al. "InAs/InP quantum dash buried heterostructure mode-locked laser for high capacity fiber-wireless integrated 5G new radio fronthaul systems." Opt. Express 29(11), (2021): 16164–16174. https://doi.org/10.1364/OE.424504.

Liu, G., et al. "InAs/InP quantum dot mode-locked laser with an aggregate 12.544 Tbit/s transmission capacity." Opt. Express 30(3), (2022): 3205–3214. https://doi.org/10.1364/OE.441820.

The base of a control box contains the subassembly parts fixed to the box with small screws, with 11 red, white and yellow wires running from subassembly out through the sides of the control box.

Quantum lasermilitary

Cabrol has written over 400 peer-reviewed articles and conference proceeding papers and several books, and is the recipient of a number of research awards. She was married to Edmond A. Grin, a hydrogeological engineer.[2] The two have written books and papers together, including La recherche de la vie dans l'univers (2000), Lakes on Mars (2010) and From Habitability to Life on Mars.[8][9] In 2008 alone, Cabrol produced 17 papers.[2] In 2023 she published the book The Secret Life of the Universe.[10]

The demand for broadband high-speed wireless connectivity with low latency and reliability has been driving 5G and beyond wireless communications, with usage scenarios that specify high-speed broadband services with peak data rates of tens of Gb/s. To achieve such ultra-high-speed broadband and low latency services, high carrier frequencies in the millimeter wave (mmW) bands (30 GHz to 300 GHz) are of great interest. However, generating mmW signals with traditional electronic methods becomes increasingly difficult as the frequency increases, and the transmission of those signals over long distances is a real challenge. Consequently, in the optical domain, broad-bandwidth, simple, efficient and cost-effective photonic millimeter-wave-over fibre (mmWoF) solutions are considered viable alternatives for mmW signal generation, processing, control and distribution for application in broadband wireless access networks. The generation of mmW signals can be addressed using optical techniques based on the heterodyne beating of two optical signals, spaced at the desired mmW frequency where digital or analog data are encoded onto either one or both optical signals.

Cabrol was born near Paris, France. She attended Nanterre University and the Sorbonne (master's degree; Ph.D., 1991). In 1986 she became the first person to extensively study the Gusev Crater on Mars. She attracted the interest and praise of Valery Barsukov of the Soviet Academy of Sciences, who invited her to Moscow to give a lecture.[2]

Zeb, K., et al. "Broadband optical heterodyne millimeter-wave-over-fiber wireless links based on a quantum dash dual-wavelength DFB laser." J. Light. Technol. 40(12), (2022): 3698–3708. https://doi.org/10.1109/JLT.2022.3154652.

For those interested in developing quantum dot lasers and other advanced optoelectronic devices, the CPFC allows clients to retain their design IP while leveraging a process-related IP toolbox capable of supporting high-reliability, high-yielding process blocks needed for leading-edge designs—including buried heterostructures (BHET) lasers and multi-regrowth DFB lasers, electro-absorption modulated lasers (EML), avalanche photodetectors (APD) and focal plane arrays (FPA) photodetectors, semiconductor optical amplifiers (SOA) and gain chips, and the interconnects and waveguides to build photonic integrated circuits. The CPFC has a team of commercially facing experts that work closely with customers throughout the device fabrication process to develop customized solutions that meet their specific needs and requirements.

The labels of the parts of an optical design in exploded view, in no specific order, are detector, fibre, 25 GHz etalon, laser, collimating lens, beamsplitter 70/30, isolator/beamsplitter 98/2, and focusing lens.

Cabrol is a member of NASA's Mars Exploration Rover mission.[4] She is also a WINGS WorldQuest Carey Fellow as well as an Air and Space WINGS WorldQuest Woman of Discovery laureate.[5]

Quantum laserprice

The 3D schematic shows the 5 constituent parts of a quantum dot laser: top contact, ridge waveguide, laser core, substrate and bottom contact. Cutout of a highly magnified image shows the surface of a quantum dot layer in the laser core, covered with many bubble-like structures of various sizes.

Our QD lasers are based on conventional InP semiconductor lasers, which are ubiquitous in the optical telecommunications and data communications sectors. But in ours, the QW gain section has been replaced with QDs (see figure 1). This approach means that laser fabrication can be performed using all of the standard InP processing techniques available at the NRC, including grating fabrication and the creation of buried heterostructures.

Since the mid 1990s, the National Research Council of Canada (NRC) has been heavily involved in developing quantum dots and dashes on both GaAs and InP substrates. In particular, applications in the 1.55 µm wavelength range have driven the growth of self-assembled InAs quantum dots on the InP-based platform. These QDs have been used to demonstrate lasers with performance advantages in high-speed data communications applications over QW lasers.

Nathalie A. Cabrol (French pronunciation: [natali kabʁɔl] ⓘ) (born August 30, 1963 [1]) is a French American astrobiologist specializing in planetary science. Cabrol studies ancient lakes on Mars, and undertakes high-altitude scientific expeditions in the Central Andes of Chile as the principal investigator of the "High Lakes Project" funded by the NASA Astrobiology Institute (NAI). There, with her team, she documents life's adaptation to extreme environments, the effect of rapid climate change on lake ecosystems and habitats, its geobiological signatures, and relevance to planetary exploration.

Mode-locking a semiconductor laser is an attractive way to produce a frequency comb but usually requires multi-section devices and very precise control of the operating conditions in order to maintain the high-quality comb required for coherent communication applications. The unique properties of the QD gain material allows these lasers to readily mode-lock using a very simple, easily controlled single-section Fabry–Perot laser cavity.Footnote 3 There is no requirement for separate saturable absorbers or multiple electrical contacts, and the range of operating conditions (e.g. drive current, temperature) where good mode-locking occurs is large. All of the modes are mutually phase-locked, making them ideal for coherent communication.

Quantum laserDARPA

3D schematic of a quantum dot laser. Cutout with atomic force microscope image shows the surface topography of a layer of quantum dots in the laser core substrate layers.

A common approach to generating the mmW beat signal is to use 2 separate lasers operating at 2 different wavelengths. The disadvantage of this scheme is that, without complex control systems, the two lasers can drift relative to each other, introducing noise in the mmW signal generated. To address this issue, we generate both wavelengths in a single laser cavity, which minimizes relative drift between the two lasing lines and is made possible through the use of the QD gain medium. This results in high optical power per mode and high spectral purity with low relative intensity and low-phase noise. Importantly, this makes the device comparatively simple and compact. As a result, the QD dual-wavelength laser has the advantage of reducing system complexity and cost, showing the potential to offer a simple and low-cost solution for 5G optical heterodyne mmWoF systems.

Between 1985 and 1994 Cabrol conducted planetary geology research with her husband, Edmond Grin, at the Paris-Sorbonne University and Observatoire de Paris-Meudon of France. As their lab was being shut down in 1994, a visit from NASA scientist Christopher McKay resulted in Cabrol's move to the US that same year[3] as a NASA postdoctoral researcher. She and her husband remained in the country and became US citizens.[4] Cabrol was the spokesperson for the selection of Gusev crater as the landing location of NASA's Spirit rover on Mars.[2] In 1998, she became a NASA contractor through the SETI Institute, continued her Mars research there and was elevated on 7 August 2015 to the director of the Carl Sagan Center.[5]

The NRC's Canadian Photonics Fabrication Centre (CPFC) is a state-of-the-art III-V, InP pureplay foundry located in Ottawa, Canada. The CPFC offers a range of fabrication services, from prototyping, through to full-scale volume manufacturing. The CPFC's facility is equipped with the latest tools and equipment for processing photonic devices and photonic integrated circuits. The CPFC offers a range of services:

The line graph for 47 gigahertz mode spacing shows the intensity of light that a laser emits as a function of wavelength represented by 2 lines, one line for 60 milliamperes drive current and one line for 200 milliamperes drive current. The x-axis is labelled "wavelength (nm)" and the y-axis is labelled "intensity (dBm)".

Lu, Z., et al. "InAs/InP quantum dash semiconductor coherent comb lasers and their applications in optical networks." J. Light. Technol. 39(12), (2020): 3751–3760. https://doi.org/10.1364/OE.441820.

Since January 2015, she has been the PI of the SETI Institute NASA Astrobiology Institute (NAI) team that seeks to understand the impact of rapid environmental change on habitability and biosignature potential on Mars. She explores high-altitude lakes in the Andes where environmental conditions are analogous to early Mars. With her team, she has climbed the 19,731-foot (6,014 m) Licancabur volcano on numerous occasions to conduct studies, freediving in the crater lake.[6] Her lake exploration activities, searching for extremophiles (microbes with the ability of surviving in harsh environments) gave her the unofficial woman's record for the free diving and scuba diving conducted at the highest altitude.[2] Cabrol found an abundance of life, including new species and a massive field of fossilized microbial mats, called stromatolites. She collected microorganisms from the lake. She recalls her "astonishment at the richness of organisms at those altitudes, despite the harsh conditions".[2]

Arakawa, Y., and Sakaki, H. "Multidimensional quantum well laser and temperature dependence of its threshold current." Appl. Phys. Lett. 40, (1982) 939–941 https://doi.org/10.1063/1.92959.