Using a parfocal lens allows you to zoom in to a subject for focusing but then zoom out again for creating your desired composition without worrying that your focus will be thrown off in the process.

To start building a custom gear, we need 2 measurements - the width and diameter of the focus ring. Outside diameter (OD) is optional. If no outside diameter is specified, it will be made as a standard low profile. Low profile gears usually have between 3 and 6mm (less than 1/4") thickness for a clean, low profile gear that slides easily into your current lens case or bag.

Lenses ideally exhibit minimal focus breathing, as it can result in changes in composition for still photographers, and an unwanted visual effect when shooting video.

Parfocal lenses are generally more expensive than varifocal lenses. Advantages of parfocal zoom lenses may also include an increased zoom range, smaller dimensions, and lower weight.

Despite the overwhelming presence of and preference for autofocus lenses, there are plenty of manual focus lenses available. These are mostly used in special situations such as night, macro, and landscape photography when super-precise focusing is required or autofocus may not work properly. Manual focus lenses are usually less expensive than autofocus lenses.

We hope this beginner’s guide to lens features was helpful as you try to wrap your head around the difference between various lenses on the market.

Lens manufacturers have added stabilization modes to improve performance in special situations. Most telephoto lenses come with a Mode 1 and a Mode 2. Mode one is general purpose and best for stationary subjects. Mode 2 is for panning – following subjects moving in a straight line such as a car or runner. Some lenses have a Mode 3. This is for photographing subjects that moving erratically such as athletes on the field or birds in flight.

Most lenses these days are autofocus lenses. There is usually a switch on the lens, or an option in the camera’s menu, to change to manual focus if you want to fine-tune your focus or if the autofocus isn’t functioning properly, which can sometimes happen in low light situations if there isn’t enough contrast in the scene.

The lens aperture controls how much light enters the camera through the lens. It also affects the depth of field. Aperture settings are called f-stops. It might seem counterintuitive, but a high f-number means a smaller aperture opening with less light coming through, while a low f-number means a wider aperture and more light hitting the sensor.

If you've got a set of digital calipers, those are absolutely the best method of measuring. They are very precise and ensure that your gear will fit right with as few adjustments as possible. If you don't have calipers, here's a link to the same ones we use.

Nikoncamera lens components

DSLR vs. Mirrorless. There’s also a difference between DSLR and mirrorless lenses, and lenses made for APS-C and full-frame cameras. DSLR and mirrorless cameras also have different mounts, even when made by the same manufacturer, so make sure you’re buying the right lens. Canon and Nikon make adapters that allow you to use one of their DSLR lenses on one of their mirrorless cameras without a problem. There are also some third-party manufacturers that also make adapters. However, they don’t always work as well as in-house adapters.

About the author: John Tunney is a fine-art photographer and instructor living on Cape Cod in Massachusetts. You can find his work on his website and on Instagram.

Higher-end lenses often come with weather sealing, which is designed to keep out water and dust. It usually involves seals around switches, connections, and other areas that might allow the elements to sneak in. However, there’s no standard definition of weather sealing and weather sealing doesn’t mean weatherproof. Nonetheless, it’s a good idea to check for weather sealing when buying a lens if you plan to shoot outdoors in a challenging environment.

Focus-by-wire systems focus more quickly than linear systems when using autofocus. However, they can be harder to focus when trying to focus manually. With a linear system, each position of the focus ring corresponds to a specific distance from the lens. This allows the manufacturers to put distance markers on the lenses, which is very helpful in some situations. With focus-by-wire, the position of the focus ring doesn’t correspond to a specific distance.

Want to suggest a term or feature that isn’t currently on this list? Leave a comment below and we will consider adding it!

If you can't find a gear for your lens, please take a moment to fill out a custom gear form. Custom gears are only available inside the US and are $45.00.

Mustache distortion is a combination and barrel and pincushion distortion. Straight lines toward the center of the image bow outward away from the center, while those on the edges bow inward toward the center.

We can sometimes do custom work outside the US. To ensure our work is at the highest standard with fast turn around times, we make adjustments to any custom made gear for no additional cost and ship the replacements to you. Newly made custom gears usually require at least one adjustment. If you are outside the US, custom work does take a little bit longer because of necessary shipping time and even longer if the gear needs adjustments made. Of course, expedited world wide shipping is available at checkout. If that is acceptable, please submit a form below and we will review the gear design and begin work.

A parfocal lens is a type of camera lens that is able to maintain its focus plane even when the lens is zoomed in or out. This means that when the focal length of the lens is changed, the point of focus will remain the same, which can be useful in certain photography situations, such as when photographing a moving subject.

Lens coatings are thin layers of material that are applied to the surface of camera lenses to improve their performance. There are several types of lens coatings, each of which serves a specific purpose. Some common types of lens coatings include:

Parts of alensPhysics

Focus breathing is when the angle of view of a lens changes as the focus is changed. The name comes from the appearance of a lens “breathing” in and out as a photographer adjusts the focus ring back and forth.

While a lens can be as simple as a pinhole or a single lens element, modern camera lenses are typically created using multiple lenses in different groupings. These lenses have different shapes, materials, and qualities, and each group can have a different function within the entire lens system.

Pincushion distortion is the opposite. Lines away from the center start to bow inward toward the center. It’s an effect you’ll see with telephoto lenses.

Camera lens componentsexplained

Lenses have either a focus-by-wire or linear focusing system. Focus-by-wire is an electronic focusing system while linear focusing is a mechanical system.

On this lens, fit ring #67 fits perfectly and turns the focus ring without slipping. It fits exactly how the gear should fit, so let us know which # ring works best and we'll mail the corrected gear to you.

Bokeh is a Japanese word meaning blur. It refers to the quality of the blurry areas of an image. Good bokeh has a smooth, creamy look to it while bad bokeh has a rougher look with distinct edges. For example, the edges of a bright point of light will blend smoothly into the background if a lens has “good” bokeh.

There’s more to consider than focal length and price when buying a new lens. Lenses come with an assortment of features such as stabilization and weather sealing, plus issues like distortion and bokeh. Here is a guide to help you understand some of the topics and help you make the right choice in your next lens.

We'll include a set of fit rings you can try on the focus ring in the event your gear doesn't fit properly. There will be 10-15 numbered fit rings with slightly different inside diameters, in the same size range as the measurement you provided. Try them on the focus ring of your lens until you find one that fits tightly enough to turn the focus ring without slipping. We can make very precise adjustments based on which # ring fits best. We will adjust it and mail it free of any additional charges. It's not unusual for some little fine- tune adjustments for a perfect fit. It's well worth the time and effort to request adjustments if needed. After all, your lens is a serious investment in yourself and your work, and our gear should compliment that investment with the same degree of professionalism.

We highly recommend you use a digital calipers to measure. However, if you don't have access to calipers, lenses can be measured using only a paper strip. There are a few things you should know before using a paper strip though - the measurement is usually not as accurate and the gear may or may not fit as perfectly. We'll still adjust the gear if needed.

With a focus-by-wire system, when you adjust the focus ring you send a signal to adjust the optics and focus the lens. With a linear system, you actually adjust the optics when you turn the focusing ring.

There are a couple of exceptions. Leica, Sigma, and Panasonic created the L-mount alliance, which means their customers can mix and match lenses with their L-mount cameras. Olympus and Panasonic created the Micro Four-Thirds camera. Their customers can use lenses from either manufacturer.

A lens element is a single piece of glass or other transparent material that is used in a camera lens to refract (bend) light. Camera lenses can contain one or more lens elements, and the number and type of elements can vary depending on the design of the lens.

Finally, there are also some brands, such as Sigma and Tamron, that produce 3rd-party lenses compatible with cameras from major manufacturers. These lenses typically aim to provide equal (or even better) image quality and features at a lower price point compared to the camera manufacturer’s own lenses.

All lenses are said to have at least some amount of chromatic aberration, but some have more than others. Fortunately, it is easily removed or reduced in post-processing in Lightroom and other editing programs.

Camera lensparts and functions

UV coatings: These coatings help to block ultraviolet (UV) light, which can cause color shifts in images and can be harmful to the human eye.

You’ll see this most often in astrophotography when stars along the outer edges of the image look more like comets than points of light. You can’t correct coma in post-processing, but you can reduce it by using a higher f-stop. However, you probably don’t want to use a high f-stop if you’re photographing the night sky. Look for a lens with little or no coma if you plan to shoot the stars.

Adding image stabilization to a lens makes the lens a little heavier, which somewhat ironically increases the need for image stabilization.

Camera lensparts diagram

Expenses lenses geared toward professionals typically exhibit less focus breathing than cheaper, lower-end lenses aimed at beginners.

APS-C vs. Full frame. Lenses made for full-frame cameras will work perfectly on APS-C cameras, but lenses made for APS-C won’t work on full-frame cameras because of the smaller field of view.

Glass lens elements may struggle with chromatic aberration, so manufacturers may include some low-dispersion elements created with other materials (e.g. fluorite) with lower refractive indexes in order to reduce those aberrations.

Camera lenses have three types of optical distortion: barrel, pincushion, and mustache. An image with barrel distortion looks fine in the center but starts to curve toward the edges. Lines on opposite sides of the center appear to bow outward like the edges of a barrel. You’ll see this effect with wide-angle lenses.

Digitalcamera lens components

You may be able to limit it while shooting, too, by shooting at a higher f-stop. For example, on a lens with bad chromatic aberration, you’ll probably see more of it at lower f-stops than at higher f-stops. For example, you’ll get more fringing at f/4 than you will at f/16.

When looking at the specs of a camera lens, you may have noticed that the manufacturer often shares the number of lens elements and the number of groups those elements are arranged in.

A lens with “bad” bokeh will show distinct edges around the circle of light and may even display “onion ring’ bokeh – a bright point of light will have rings within it, like the rings within an onion or tree.

Camera lens componentsand functions

Everybody shakes. This can result in camera shake and blurry pictures for still photographers and jitter in video. This is especially true with long shutter speeds or with large and heavy telephoto lenses. Many lenses now come with some form of image stabilization, a system designed to compensate for shaking and help you get a sharp image. Image stabilization also lets you use a longer shutter speed so you can get sharp images in low-light situations.

Anti-reflective coatings: These coatings help to reduce the amount of light that is reflected off the lens surface, which can help to reduce flare and ghosting in images.

Water- and oil-repellent coatings: These coatings help to prevent water and oil from adhering to the lens surface, which can make it easier to clean the lens and can help to improve image quality.

Lens mounts. Most camera manufacturers have a proprietary lens mount, which means you can’t mix and match lenses from different camera manufacturers. Canon lenses won’t fit on Nikon or Sony cameras and vice versa.

There’s also in-body image stabilization (IBIS). This is a system built into the camera to reduce camera shake, which is helpful when using a lens without image stabilization. Some systems combine IBIS with lens stabilization for better overall stabilization.

You can wrap this around your lens's focus ring and read it from the zero mark to find the circumference of the focus ring. You can also use this to find the width of the focus ring - the distance from front edge of focus ring to the back edge.

Certain shapes may be used in other elements to improve image quality in other ways. For example, aspherical lens elements are often used to combat distortion in wide-angle lenses and to reduce spherical aberrations in fast lenses.

Camera lens componentsdiagram

Lens manufacturers use different terms for image stabilization. Canon, for example, calls it Image Stabilization (IS). Nikon calls it Vibration Reduction (VR). For Sony, it’s Optical Steady Shot (OSS). Tamron uses Vibration Compensation (VC) and Sigma uses Optical Stabilization (OS). It’s all pretty much the same thing.

If you expect to be doing a lot of photography indoors or in other low-light settings, you probably want a “fast” lens. This is a lens with a low f-stop setting such as f2.8, f2 or lower. Also, some zoom lenses have variable apertures. For example, a 100-400mm zoom might be f/4.5-5.6. This means that it will go down to f4.5 at its shortest focal length, but will only go to f5.6 as you zoom in and go to longer focal lengths.

Our new line of HD Seamless™ Follow Focus Gears are available for custom work on request. Pricing on HD gears varies according to dimensions. If you're unfamiliar with our HD gears, they're simply made to at a finer resolution. The most noticeable difference is their flawlessly-smooth, highly professional surface finish. Otherwise they do the exact same job as standard focus gears - full functionality, a perfect fit, and high degree of customizability, just like you can always expect from us.

Lens coatings can be applied to the front and/or rear elements of a lens and can be made from a variety of materials including polymers, metals, and ceramics.