handi-vac bags

The Fisher Scientific Encompass Program offers items which are not part of our distribution portfolio. These products typically do not have pictures or detailed descriptions. However, we are committed to improving your shopping experience. Please use the form below to provide feedback related to the content on this product.

The best possible performance is achieved through the use of cooled hybrid APD receivers. Cooling improves noise by reducing bulk dark current, and temperature stabilization eliminates gain variations with temperature. Performance achieved with standard APDs includes detection of 100-photon, 20-ns pulses at 830 nm. At the other end of the spectrum, the expected emergence of low-cost/high-volume APDs is likely to extend their use in recreational rangefinders for golfing or hunting and in automobile collision-avoidance systems. Rangefinding performance in these applications is currently limited by the use of PIN detectors and short pulsewidths mandated by eye-safety requirements.

We keep science moving forward by offering over 2.5 million products and extensive support services to the research, production, healthcare, and science education markets. Count on us for an unrivaled selection of lab, life sciences, safety, and facility management supplies—including chemicals, equipment, instruments, diagnostics, and much more—along with exceptional customer care from an industry-leading team that’s proud to be part of Thermo Fisher Scientific.

The effectiveness of an APD system for photon counting depends on two important specifications. The first is the photon-detection efficiency of the APD, representing the probability that a photon is detected and then generates an avalanche of sufficient magnitude to trigger a comparator circuit. The second is the system`s recovery time after a detection event during which the APD cannot detect photons, referred to as "dead time."

The two principal ways of configuring an APD circuit for photon counting use either a passive or active quench circuit.2,3 A passive quench circuit uses a load resistor to limit APD current to below the level at which continuous discharge occurs. The RC time constant of the circuit determines the recharge rate, with typical dead times of approximately 300 ns. Maximum count rates of approximately 106 counts/s limit use to applications with low count rates.

In selecting an APD, it is important to effectively compare competing manufacturers` specifications. Significant parameters include responsivity, dark current, noise, and temperature coefficient.

Operating specifications. The responsivity and dark current of APDs is often specified at a percentage of breakdown voltage (that is, R(l) at VR = 0.9VBR). However, variations in the gain and noise vs. voltage characteristics of a specific APD type, or between competing designs, prevent valid comparison of APD characteristics using this method. This method does not imply measurement at equal gain and only indicates typical characteristics.

Handi vactweezer

SERGE MELLE and ANDREW MACGREGOROptical measurement plays an important role in a variety of scientific, medical, and industrial applications. Simple optical systems use inexpensive photocells for light detection, but many applications require higher accuracy or enhanced sensitivity. Traditionally, high sensitivity has been obtained using photomultiplier tubes (PMTs). However, the photon-level sensitivity of PMTs comes at the expense of price, fragility, sensitivity to magnetic fields, size, and high-voltage power-supply requirements.By contrast, semiconductor detectors offer small size, ruggedness, and ease of use. Manufactured using proven wafer-scale silicon or III-V batch-processing techniques, they are inherently cheaper and provide better than 70% quantum efficiency beyond 400 nm. The workhorse semiconductor detector is the PIN photodiode. In some applications, however, PIN photodiodes cannot match the sensitivity of PMTs, and avalanche photodiodes (APDs) should be considered. The high sensitivity of APDs rivals that of PMTs, leading to their use in a variety of applications including blood analysis, laser rangefinding, fiberoptic communications, barcode scanners, single-photon counting, and particle detection (see photo).What is an avalanche photodiode?An APD differs from a PIN photodiode by providing internal signal gain. Output signal current, IS, from an APD is IS = Ro MPS, where Ro (amps/watt) is the intrinsic responsivity of the APD, M is the gain, and PS (watts) is the incident optical power. The internal gain of an APD is dependent upon the APD reverse voltage, VR, and provides greater detection sensitivity than a PIN receiver when the latter`s sensitivity is limited by preamplifier noise (see Fig. 1).

Responsivity and gain. For many APDs, it is not practical to make an accurate measurement of intrinsic responsivity, RO, making it inappropriate to state sensitivity at M = 1. Rather, an operating voltage should be specified for a given responsivity. Diode-diode variations lead to a distribution in the operating voltage, and manufacturers should also specify a voltage range within which a specific responsivity will be achieved.

Reynolds Handi-Vac

Optical measurement plays an important role in a variety of scientific, medical, and industrial applications. Simple optical systems use inexpensive photocells for light detection, but many applications require higher accuracy or enhanced sensitivity. Traditionally, high sensitivity has been obtained using photomultiplier tubes (PMTs). However, the photon-level sensitivity of PMTs comes at the expense of price, fragility, sensitivity to magnetic fields, size, and high-voltage power-supply requirements.

APDs are generally recommended for high-bandwidth applications or where internal gain is required to overcome preamplifier noise. The following steps can be used to select the appropriate detector:

Temperature coefficient. APD breakdown voltage increases with temperature, and gain is thus temperature-dependent. Usually a few percent per degree Centigrade, this dependence must be specified and compensated for in the bias supply or overall system design.

Dark current and noise. Total APD dark current includes surface and bulk leakage currents, the latter being multiplied by APD gain. At M = 1, dark current noise is dominated by surface current, which may contribute significantly less noise than multiplied dark current at operating gain. Therefore, APD dark current and spectral noise should be specified at the operating responsivity or gain.

One of the key parameters to consider when selecting an APD is noise performance. Like other detectors, an APD will be operating in one of two noise-limited detection regimes. Sensitivity will be limited by dark-current shot noise or preamp noise at low light levels and by signal shot noise at higher powers. However, APD noise performance is degraded by an excess noise factor, F, and provides a S/N at higher powers that is worse than a PIN detector with the same quantum efficiency. It therefore makes sense to replace a PIN with an avalanche photodiode if preamplifier noise exceeds the quadratic sum of the PIN detector noise and photon shot noise on the signal.

The Handi-Vac-2 has an improved tip designed for better lifting capacity utilizing larger, non-marking vacuum cups. This new tip also enhances functionality and improves accuracy when picking and placing parts. One static-dissipative cup included. The entire vacuum tool is ESD-safe.

High-speed receivers. Avalanche photodiodes are used in high-bandwidth receiver modules for fiberoptic communication systems to provide greater S/N compared to a PIN receiver. Typical fiberoptic systems transmit 1310- or 1550-nm light pulses at 622 Mbit/s or 2488 Mbit/s over single-mode fiber and use InGaAs detector-based receivers.

handi-vac vacuum pen

To understand why more than one APD structure exists, one must consider the trade-offs accommodated by the APD designer. The ideal APD would have zero dark noise, no excess noise, broad spectral and frequency response, a gain range from 1 to 106 or more, and low cost. More simply, an ideal APD would be a good PIN photodiode with gain! In reality, this is difficult to achieve due to the need to trade off conflicting design requirements. Some of these trade-offs and how they are optimized in commercial APDs are discussed below.

HV-KIT-ESD

By contrast, semiconductor detectors offer small size, ruggedness, and ease of use. Manufactured using proven wafer-scale silicon or III-V batch-processing techniques, they are inherently cheaper and provide better than 70% quantum efficiency beyond 400 nm. The workhorse semiconductor detector is the PIN photodiode. In some applications, however, PIN photodiodes cannot match the sensitivity of PMTs, and avalanche photodiodes (APDs) should be considered. The high sensitivity of APDs rivals that of PMTs, leading to their use in a variety of applications including blood analysis, laser rangefinding, fiberoptic communications, barcode scanners, single-photon counting, and particle detection (see photo).

Preamplifier input noise limits PIN receiver sensitivity. To remedy such problems, an APD is therefore used to provide signal gain before the preamp input. The increased S/N permits effective processing of the output by subsequent receiver electronics. Sensitivity can be increased 6 to 8 dB at 2.5 Gbit/s using InGaAs APDs. This increases transmitter-receiver spacing in a typical fiberoptic transmission system by up to 30 km, reducing cost outlays for transmission equipment.

A typical fiberoptic receiver mates a detector and transimpedence amplifier (TIA) to provide a voltage output for interfacing to clock recovery, signal reshaping, and decision circuits. The amplifier circuit typically uses a FET-input hybrid circuit or monolithic TIA integrated circuit. Noise is dominated by the combination of Johnson noise from the low feedback impedance required for extended bandwidth and total input capacitance.

Avalanche photodiodes are available spanning a wide spectral range. Silicon APDs are used between 400 and 1100 nm, germanium between 800 and 1550 nm, and indium gallium arsenide (InGaAs) between 900 and 1700 nm. Although more expensive than germanium, InGaAs APDs provide lower noise and higher frequency response for a given active area. Germanium APDs are recommended for applications in which amplifier noise is high or cost is a prime consideration.

By clicking Submit, you acknowledge that you may be contacted by Fisher Scientific in regards to the feedback you have provided in this form. We will not share your information for any other purposes. All contact information provided shall also be maintained in accordance with our Privacy Policy.

where q is electron charge and F is the excess noise factor (see below). Total receiver noise (iN(TOT)) equals the quadratic sum of APD and amplifier noise, (iN(AMP)), given by

Continued research and development of new APD structures promises to broaden their use in a range of applications. Large-area APDs with active areas up to 100 mm2 are being developed as PMT replacements and for nuclear-particle detection, either directly or using scintillator crystals. Superlattice III-V APDs using quantum-well structures for low-noise and high-gain-bandwidth products are being developed to enhance receiver sensitivity in fiberoptic systems operating at rates of 10 Gbit/s or more. These and other developments will augment the capabilities of optical systems and increase their importance in everyday applications.

An APD/amplifier combination is used to detect the faint return reflections from the target. Receiver bandwidth (B) is typically designed so that B ª 0.35/t. For optimal timing resolution of the return pulse, higher bandwidths within S/N design limits are used. The S/N depends on the collection optics and receiver combination. For optimum S/N, a design/cost compromise must be struck between fast optics (low f-number), detector diameter, and preamp type. Hybrid APD/preamplifier receivers offer up to five times better sensitivity than use of external high-frequency preamps but are more expensive.

The k factor, kEFF, can be measured experimentally or calculated theoretically from the carrier-ionization coefficients and the electric-field profile of the APD. Many manufacturers approximate F using an empirical formula, given as

All APDs generate excess noise due to the statistical nature of the avalanche process. The excess noise factor given by F is the factor by which APD shot-noise performance is degraded compared to a PIN detector. The excess noise factor is a function of the carrier-ionization ratio, k, defined as the ratio of hole to electron ionization probabilities (k 1). Excess noise can be calculated using the model developed by McIntyre,1 which considers the statistical nature of avalanche multiplication. The excess noise factor is given by

For a shorter dead time and higher photon-detection efficiency (up to 60%), an active quench circuit is recommended. By actively forcing the APD reverse voltage below VBR immediately upon initiation of an avalanche pulse, the diode discharges completely before the high voltage is reapplied. Recharging is done rapidly using a low-value load resistor or transistor. A typical active quench circuit lowers dead time to 35-50 ns and is recommended in higher photon-flux applications.

Avalanche-photodiode noise is caused by dark current and photocurrent shot noise, (In(SHOT)). This derives from the random fluctuations in current flow. For a PIN detector this is given by

Laser rangefinding. The most common application of APDs is in rangefinding, either in free space (laser rangefinding or lidar) or within optical fibers with instruments such as optical time-domain reflectometers (OTDRs). Laser rangefinders typically use 905-nm or 1.06-µm pulsed laser transmitters with peak powers from 10 W to kilowatts and pulsewidths (t) between 5 and 100 ns, while OTDRs operate at 1300 or 1550 nm.