Please do not enter personal data here. (See also our privacy declaration.) If you wish to receive personal feedback or consultancy from the author, please contact him, e.g. via e-mail.

Different kinds of lenses can be used in collimators. For standard telecom fibers and in fact many others, one mostly uses GRIN lenses (gradient-index lenses), as these are relatively cheap and small. However, they are less suitable for larger beam diameters, e.g. of more than a few millimeters. In such cases, one tends to use conventional singlet or doublet lenses, which may be of spherical or sometimes aspheric type. This is needed, for example, when a collimated beam needs to be transmitted over a large distance, such as in free-space optical communications, where a long Rayleigh length is required.

Circular polarized 3D glasses, on the other hand, take sophistication to the next level. Each lens allows light waves that rotate in a certain direction (clockwise or counterclockwise) to pass through. Unlike their linear counterparts, these glasses don't require you to maintain a fixed head position. Your head can tilt freely, and the 3D effect remains intact, thanks to the circular polarization technology.

O/E Land's fiber collimators and focusers are available as fixed or adjustable versions, in fiber-pigtailed or receptacle form, also with customized designs.

How polarized3Dglasses work

A shorter wavelength usually leads to a somewhat smaller mode size, but nevertheless to a lower beam divergence and to a smaller output beam radius. This holds even more if the fiber gets into the multimode regime for sufficiently short wavelengths. For such reasons, a visible pilot beam for an infrared beam, for example, may not accurately show the size of the infrared beam. Also, the correct fiber positioning for collimation may depend on the wavelength, particularly if no achromatic lens (see below) is used.

Another application is the combination with a back-reflecting mirror and some additional optical element. For example, one may insert a Faraday rotator in order to obtain a fiberized Faraday mirror, or a quarter-waveplate for an effective half-waveplate reflector. In other cases, one may be using some optical filter or a saturable absorber.

Angled fiber ends are often used to suppress back-reflections from the fiber end face into the core, i.e., to maximize the return loss. Unfortunately, the angle leads to some deflection of the output beam.

Note: the article keyword search field and some other of the site's functionality would require Javascript, which however is turned off in your browser.

A shorter focal length is mainly useful to keep the whole setup smaller. Concerning the coupling efficiency, there is no fundamental reason to choose a larger or smaller focal length.

For some fiber connectors with inclined fiber connection, this can be compensated by some tilt of the fiber fixture. Otherwise, the beam from the fiber will hit the lens at some angle. After the lens, the beam direction should nevertheless be in the direction of the fiber (assuming correct longitudinal and transverse positioning), but it will be somewhat offset from the center of the lens. That may also lead to increased insertion loss and to beam quality deterioration if some clipping, reflection or scattering occurs at the edge.

Circular polarized 3D glasses bring an enhanced viewing experience with more freedom of movement. They're perfect for dynamic environments such as home theaters or 3D rides where head movement is more likely. The downside is that they may be more expensive than linear polarized glasses due to their complex manufacturing process.

In principle, a fiber collimator can also be used “in reverse”, i.e., for launching a free-space beam into an optical fiber. However, it usually does not provide the required tools for fine adjustment (which are particularly required for single-mode fibers). That adjustment then has to be done e.g. with turning mirrors in the path of the input beam.

For multimode fibers, the beam divergence at the output (and thus the collimated beam size) depends on the launch conditions, and possibly even on the condition (e.g. bending) of the fiber. Generally, the beam divergence angle will be larger than according to the estimate for the single-mode fiber – possibly even much larger.

By submitting the information, you give your consent to the potential publication of your inputs on our website according to our rules. (If you later retract your consent, we will delete those inputs.) As your inputs are first reviewed by the author, they may be published with some delay.

The insertion loss of a single fiber collimator can be pretty small – of the order of 0.2 dB (i.e., a few percent) or even lower. It depends on various factors, such as anti-reflection coatings and dirt on the lens. It should not matter, however, whether a bare fiber or a connectorized fiber is used.

It is often necessary to transform the light output from an optical fiber into a free-space collimated beam. In principle, a simple collimation lens (see Figure 1) is sufficient for that purpose. However, the fiber end has to be firmly fixed at a distance from the lens which is approximately equal to the focal length. In practice, it is often convenient to do this with a fiber collimator (fiber-optic collimator). There are two different basic types of such devices, differing in how the fiber is mounted:

Edmund Optics offers fiber-optic collimators for FC/PC, FC/APC and SMA connectors and different wavelength ranges around 350 nm to 1600 nm.

Here you can submit questions and comments. As far as they get accepted by the author, they will appear above this paragraph together with the author’s answer. The author will decide on acceptance based on certain criteria. Essentially, the issue must be of sufficiently broad interest.

In modern 3D cinemas and particularly in 3D rides, where motion is a part of the experience, circular polarized glasses are often the standard. They ensure that the immersion remains unbroken, no matter how much the viewer moves.

At the end of the day, both linear and circular polarized 3D glasses have their place in the growing 3D market. Understanding the nuances between them is not just academic; it's a practical consideration that impacts your enjoyment of 3D content. Whether you are a consumer wanting the best 3D movie experience or a business deciding on which technology to invest in for your 3D offerings, recognizing these differences is key. As you step out, glasses in hand, ready to explore three-dimensional ventures, remember that the right pair isn't just an accessory—it's the gateway to a realm of extraordinary visual depth.

Using our advertising package, you can display your logo, further below your product description, and these will been seen by many photonics professionals.

When you select a product, just ask the manufacturer what lens is suitable for your fiber and needed collimated beam diameter. There are different technical routes for achieving optimal performance.

Polarisation 3dglasses

San Technology, Inc. has opened a specialized 3D Eyewear sales site, "Santek 3D Eyewear." We offer various types of 3D glasses with various frames (plastic, paper, clip-on) and a diverse selection of Eyewear. We accept small quantity purchases starting from one item, bulk orders of 500 pieces or more, and also offer customization for frames. We accommodate various needs, including color, frame design, shape, and the design of packaging bags.

Immerse yourself in the world of 3D entertainment with this comprehensive guide to understanding the key differences between linear polarized and circular polarized 3D glasses. Whether you're a curious movie-goer, a theme park enthusiast, or a business looking to invest in 3D technology, this post will unravel the science behind these intriguing devices. Let's dive into the world where glasses aren't just for vision correction, but for a whole new dimension of viewing experience.

Since 2006, San Technology, Inc. has supplied over 1 billion 3D eyewears and glasses to over 20 countries worldwide. We believe that we are providing the highest-quality products in the world.

Polarized3Dglasses vs Anaglyph

Further, we have many interesting case studies on the same page, with topics mostly in fiber optics. Concrete examples cases, investigated quantatively, often give you much more insight!

For calculations, the simpler case is that of a single-mode fiber. Here, the beam radius can be calculated with reasonably good accuracy using the following equation:

How should I select a collimating lens, given the beam divergence and required collimated beam diameter? Should I use a concave + convex combination to get the result if the divergence is very small?

Note: this box searches only for keywords in the titles of articles, and for acronyms. For full-text searches on the whole website, use our search page.

Polarized3Dglasses test

The same kind of device can also be used for launching light from a collimated beam into a fiber, or for fiber-to-fiber coupling: light from the first fiber is collimated with a fiber collimator and then focused into the second fiber by another collimator. Basically, fiber collimators can be seen as the natural interface between fiber optics and free-space optics.

The insertion loss for a pair of collimators, as used for fiber-to-fiber coupling, may be substantially higher than the sum of insertion losses of the two devices. Particularly for single-mode fibers, it is important to achieve good mode matching. Obviously, both collimators should have the same collimated beam size. Depending on the exact longitudinal positioning of the fibers in the collimators, some non-zero distance between the collimators may be ideal. This also allows one to insert additional optical elements, such as optical filters or polarizers.

CSRayzer provides different kinds of fiber collimators, which can be customized for high power, focusing distance, beam spot diameter, etc. Fixed focus collimators are also available.

Fiber-optic collimators are available for different collimated beam sizes, which simply means different values of the focal length. Naturally, devices for larger collimated beams need to be both longer and larger in diameter. The largest fiber collimators are those for high-power multimode fibers as used in laser material processing or for pumping high-power lasers; they also need to be optimized for reliable operation at high optical power levels.

Schäfter+Kirchhoff offers a wide range of fiber collimators that can be used for collimating or in reverse as an incoupler. This includes the series 60FC collimators or series 60FC-SF collimators with super fine-focussing mechanism. For large beam diameters the series 60FC-T collimators can be used with integrated TILT mechanism. Special collimators 60FC-Q with integrated quarter-wave plate or made from amagnetic titanium are also available.

Polarized3Dimages

Linear polarized 3D glasses use filters that permit light waves aligned in particular directions to pass through. Imagine each lens as a fence with slats arranged horizontally and vertically; one lens only allows 'horizontal' light through, and the other 'vertical'. When viewing a screen that displays two overlapping images polarized at 90 degrees from one another, each eye receives a different image. This disparity replicates the way each eye views objects from slightly different angles in real life, yielding a 3D effect. We also offer an article here on how 3D works.

Polarized3Dglasses video player

Coupling of light into single mode fibres can be made simple with the use of a PowerPhotonic fiber coupling micro lens array. We design and manufacture standard and custom optics in 1D and 2D arrays. All products are made in high grade fused silica and capable of both high efficiency and high power handling and our unique process minimises channel cross talk due to extremely low scatter. Lenses can spheric, aspheric or freeform due to our unique manufacturing process.

Is there a reason to prefer collimators with shorter focal length if everything I need is passing from fiber to free space, doing something on the beam with bulk optics, and then passing again to fiber? Since longer focal length ensures bigger beam radius, so less divergence, I don't get how I can chose the best collimator.

Special requirements may lead to the use of special lenses. For example, achromatic doublet lenses are used if beams with quite different wavelengths need to be handled, as otherwise proper collimation may not be achieved for all wavelengths. Aspheric lenses may be used in cases with large beam divergence from the fiber (i.e., for fibers with small mode radius) in order to eliminate spherical aberrations.

Currently, our direct shopping page is designed for orders from Japan. However, we welcome orders from customers outside of Japan. Please submit a direct inquiry using the form below or send an email to s.shop@santek3d.jp .

It is also assumed that the distance between fiber end and lens is close to the focal length <$f$> of the lens. If the distance is too small, the beam will diverge, and for too large distances it converges to a focus at some distance. It can be useful to get slightly into that latter regime, where a beam focus (with a beam diameter slightly below that at the collimator) is reached in a suitable working distance. The longer the focal length, the less critical is the longitudinal positioning.

The housing of the lens easily connects to fiber-optic cables either with FC/PC or with SMA connectors and enables Z-axis alignment.

3D glasses are the magic portal to witnessing the awe-inspiring depth and realism that 3D movies and rides offer. These seemingly simple eyepieces play a huge role in enhancing our entertainment experiences. As advancements continue, it's essential to understand the two main types of polarization used in 3D glasses: linear and circular. What are they, how do they work, and where are they applied? This article will guide you through these critical questions.

Note that a smaller mode size of the fiber implies a larger beam divergence and thus a larger collimated beam for a given focal length.

There are also fiber launch systems with additional adjustment tools for different degrees of freedom, allowing the launch of a non-adjustable input beam.

Polarized3Dglasses video

The simplicity of linear polarization makes these 3D glasses cost-effective and a great choice for passive 3D systems. However, their major limitation is the "sweet spot" for viewing. Tilting your head can disrupt the 3D effect since the alignment between the lenses and the screen changes, breaking the precise orientation required for the illusion.

This assumes that the beam profile of the fiber mode has an approximately Gaussian shape, so that we can apply the corresponding formula for the beam divergence half-angle <$\theta_\rm{fiber}$>.

Some fiber-optic collimators have adjustment screws for controlling the beam direction (by an integrated tilt adjustment) or possibly even for the fine longitudinal positioning (adjustment of focusing or working distance). Others don't have such adjustment options, and one may position and align the whole collimator with additional opto-mechanics.

Polarisation 3dcamera

The core differentiation between the two types lies in the viewer's ability to maintain the 3D effect irrespective of head position. Linear polarized glasses demand an upright, static position while circular polarized glasses allow for movement. When choosing the most appropriate glasses, consider the environment they will be used in and the level of comfort and freedom of movement you desire during the 3D experience.

The beam radius of the obtained collimated beam depends on the circumstances. In some cases, the beam diameter is as small as the fiber diameter, e.g. 125 μm; the Rayleigh length can then be less than 1 cm. In other cases, one needs beam diameters of several millimeters or even more.

Linear polarized glasses are commonly used in 3D cinemas and rides due to their affordability. They work exceptionally well in controlled environments where seat orientation is fixed, ensuring the viewer's head remains upright, maintaining the 3D effect.

Our polarization-maintaining fiber collimator has a high extinction ratio, low insertion and high return loss. The unique processing and high-quality AR coating also enable this collimator to handle high optical powers.