LIGHT UP YOUR ADVENTURE: Ironman 4x4’s LED Light Bars allow you to see further and draw less power, with state of the art, high intensity CREE LED's for maximum light spread.

One characteristic of LEDs is that they naturally exhibit power degradation with time. Often this power degradation is slow, but there are also instances where large, rapid drops in power, or even complete LED failure, occur. LED lifetimes are defined as the time it takes a specified percentage of a type of LED to fall below some power level. The parameters for the lifetime measurement can be written using the notation BXX/LYY, where XX is the percentage of that type of LED that will provide less than YY percent of the specified output power after the lifetime has elapsed. Thorlabs defines the lifetime of our LEDs as B50/L50, meaning that 50% of the LEDs with a given Item # will fall below 50% of the initial optical power at the end of the specified lifetime. For example, if a batch of 100 LEDs is rated for 150 mW of output power, 50 of these LEDs can be expected to produce an output power of ≤75 mW after the specified LED lifetime has elapsed.

The approximate total beam power through the collimation adapter is given in the tables below and on the Specs tab. The actual power at the sample plane will be lower due to losses specific to the optical set up of the microscope. If you wish to measure the power at the sample plane for your particular microscope setup, Thorlabs also offers a microscope slide power meter sensor.

To fully support the max optical power of the LED you intend to drive, ensure that the max voltage and max current of the driver are equal to or greater than those of the LED.

The thermal dissipation performance of these collimated LEDs has been optimized for stable power output. The heat sink is directly mounted to the LED mount so as to provide optimal thermal contact. By doing so, the degradation of optical output power that can be attributed to increased LED junction temperature is minimized (see the graph to the right).

UNIVERSAL MOUNTING: Rear and side end mounting solutions, provide various securing options as well as allow the light bar to be fixed at 2 or 4 points.

Particle inspection (a subset of cosmetic surface inspection) detects particles and foreign materials on or within transparent components like clear plastic ...

Thorlabs' collimated LED assemblies can be easily connected to standard and epi-illumination ports on most readily available commercial microscopes, including Olympus, Leica, Nikon, and Zeiss. Each collimated LED consists of a mounted LED and a lamphouse-port-compatible housing that contains an AR-coated aspheric collimation optic (see the Specs tab for details). If the wavelength or output power you require is not sold on this page, our mounted LEDs and Solis® High-Power LEDs are available in additional wavelengths and output powers.

Don't see the product you're looking for on the website? Our inventory turns over fast. Call us at 206-774-2000 to see if we might have it in our warehouse.

Franklin Lighting is a family-owned lighting showroom in Sarasota, FL. and near Bradenton that sells a variety of lighting products, ranging from ceiling ...

Run 5.30 Tour 2017 ; 2017 - 5.30 Modena · 190 views. 7 years ago ; 5 30 Brighton - 21 July 2017 · 224 views. 6 years ago ; BBC Sussex 530, 21July2017 · 25 views. 6 ...

2022726 — Meet new friends——rooms with different topics and types, friends with their own characteristics. come and start this journey of meeting.

Vision Software was acquired by Electronic Arts (EA) on April 8, 1996. Vision was the leader of software sales in South Africa at the time of its purchase by EA ...

For microscope applications requiring compatibility with SM1 (1.035"-40) threading, our mounted LEDs (sold separately) can be collimated using a Ø1" lens and lens tubes. This collimation method also allows for a smaller beam size than the collimators on this page. Please see the Collimation tab on our Mounted LEDs presentation for a detailed item list and instructions.

INCREASED PERFORMANCE: The aluminum extrusion housing has been designed to keep the lights cool, ensuring the greatest LED efficiency.

The CON8ML-4 connector can be used to mate mounted LEDs featured on this page to user-supplied power supplies. We also offer a male 4-Pin M8 connector cable (item # CAB-LEDD1).

Like our mounted LEDs, the package of these collimated LEDs is in direct contact with the heat sink to provide excellent thermal management. This minimizes the degradation of optical output power caused by increased LED temperatures. Please see the Stability tab for information on the stable output intensity of these collimated LEDs. Additionally, our M365LP1, M385LP1, and M405LP1 LEDs feature a higher power output and are mounted to a larger Ø57.0 mm heat sink to increase heat dissipation and thermal stability.

Note: Please ensure your microscope is configured to directly accept an external light source. Some microscope assemblies have a permanently installed illuminator or may be otherwise incompatible with the LED light sources below.

2015916 — Field of View (FOV) = 90mm ; Working Distance (WD) = 400mm ; Sensor Size = 10.67mm – We will calculate for a 90mm horizonal FOV, in turn use the ...

Traditionally used to focus the beam in lighthouse lamps, a Fresnel lens replaces the curved surface of a conventional lens with a series of small, ...

A novel type of phase retardation plates (wave plates) representing a breakthrough in light polarization measurement and control is now commercially available.

The diagram to the right shows the male connector of the collimated LED assembly. It is a standard M8 x 1 sensor circular connector. Pins 1 and 2 are the connection to the LED. Pin 3 and 4 are used for the internal EEPROM in these LEDs. If using an LED driver that was not purchased from Thorlabs, be careful that the appropriate connections are made to Pin 1 and Pin 2 and that you do not attempt to drive the LED through the EEPROM pins.

Dec 6, 2014 — The original 4 bar is pretty dim. I do not recommend them. The 4 bar tris are good LED lights. Compact, lightweight, no bulbs to burn out, no ...

The section of the housing that holds the collimation optics is the same size for all LEDs that share the same item # suffix, regardless of the size of the heat sink.

The section of the housing that holds the collimation optics is the same size for all LEDs that share the same item # suffix, regardless of the size of the heat sink.

This tab includes all LEDs sold by Thorlabs. Click on More [+] to view all available wavelengths for each type of LED pictured below.

If you would like an estimate for installation, please make a note in the comments box when you check out, and a representative will contact you. Or call us at 206-774-2000.

The actual spectral output and total output power of any given LED will vary due to variations in the manufacturing process and operating parameters, such as temperature and current. The typical total beam power of each collimated LED is specified to help you select an LED that suits your needs. In order to provide a point of comparison for the relative powers of LEDs with different nominal wavelengths, the spectra in the plots below have been scaled to the typical total beam power of each collimated LED. This data is representative, not absolute. An Excel file containing the normalized and scaled spectra for each collimation package can be downloaded using the link below each plot.

The collimation of the beam can be adjusted by changing the position of the aspheric lens with respect to the LED. Interchanging LEDs is easy; simply unscrew one LED from the housing and replace it with a different mounted LED (sold separately). We also offer collimation packages, which can be purchased separately from these LEDs.

RT-SDR-120-24: DIN rail power supply.

Driver OptionsThorlabs offers six drivers compatible with these LEDs: LEDD1B, UPLED, DC40, DC2200, DC4100, and DC4104 (the latter two require the DC4100-HUB). The UPLED, DC40, DC2200, DC4100, and DC4104 drivers are capable of reading the current limit from the EEPROM chip of the connected LED and automatically adjusting the maximum current setting to protect the LED. See the LED Drivers tab for specifications and comparison between the drivers.

DURABLE CONSTRUCTION: Designed for all off-road conditions using the latest breather and have passed the industry leading IP67 and IP69K water and dust proof ratings.