Bundingart

TUFF-N-DRI® Barrier Board is designed for use with TUFF-N-DRI waterproofing membranes. The unique proven fiberglass design promotes efficient water drainage and the retention of the board’s R-value. Barrier Board acts as a protection course for TUFF-N-DRI waterproofing membranes.

In recent years, the growing popularity of off-site manufactured bunds has resulted in a wider choice of materials and construction methods. One option for permanent bunds is prefabricated steel. However, steel is susceptible to both atmospheric corrosion and attack by some stored chemicals, so a special resistant coating must also be applied. There have been some notable steel bund failures in the water industry, where bunds were lined with GRP (glass-reinforced plastic).

Bundingmeaning construction

TUFF-N-DRI® Barrier Board is designed for use with TUFF-N-DRI waterproofing membranes. The unique proven fiberglass design promotes efficient water drainage and the retention of the board’s R-value. Barrier Board acts as a protection course for TUFF-N-DRI waterproofing membranes.  The ability to quick set TUFF-N-DRI boards into curing TUFF-N-DRI membranes allows for same day, efficient installation of a drainage.

The chemical resistance of your bund material does not need to be as high as that of your storage tank or container, since it is not intended to contain chemicals for long periods. The general rule of thumb is that the bund should be able to resist the specified chemical for seven days.

What isbundingin agriculture

The ability to quick set TUFF-N-DRI boards into curing TUFF-N-DRI membranes allows for same day, efficient installation of a drainage.

When it comes to temporary bunds for storage tanks up to 1,000 litres, most are made from moulded low-density polyethylene (LDPE). This is similar to the material used for some chemical IBCs, drums and other containers. The material has good corrosion resistance, while its moulded construction creates a robust vessel. Steel can also be used for temporary bunds, but again it will need to be finished with a corrosion-resistant lining.

FloorBunding

Over time, a GRP lining can develop cracks or leak paths, which allow stored chemicals to contact the steel. A more resilient alternative for permanent bunds manufactured off site is plastic, and materials like polyethylene (PE), polypropylene (PP) and polyvinyl chloride (PVC), provide excellent chemical and atmospheric corrosion resistance.

Types ofbunding

It’s essential to choose a bund made from the correct material for your requirements. There are several factors to consider, including the size of your storage containers, the nature of the chemical stored, the location of the containers and the environmental conditions. The choice of material is also influenced by whether the bund will be built on site or manufactured off-site.

The wall height and floor area of a bund can be varied according to your needs. Choosing a lower wall, and a correspondingly larger floor area, will give you easier access for cleaning and maintenance, and for assessing tank condition. There is also less potential load on the sidewalls. However, low walls can be breached more easily by spigot flow – a powerful jet of leaking liquid passing over the bund wall. This risk can be countered by installing splash screens. A low wall can also be breached by the tidal wave effect caused by sudden and catastrophic tank failure.

Most traditional, site-built permanent bunds are constructed from concrete, brick or block walls, standing on concrete floors. These materials, and any mortar used in the masonry walls, must be watertight and resistant to the stored chemical.

WIMES: Water Industry Mechanical and Electrical Specifications provide detailed information on water industry standards relating to bunding. WIMES 8.02 stipulates that bund capacity should be 110% of the total storage capacity of the largest tank or 25% of the total capacity of all tanks, whichever is the greater. If tanks are connected during operation, bund capacity should be 110% of their combined storage capacity.

Firstly, the plastic welds on plastic permanent bunds are not usually as strong or resistant to chemicals as the base material. Therefore, the bunds need to be well designed and reinforced to provide the required strength. Like any bund, they must be strong enough to contain the specified chemical, and to withstand any shock load created by a full tank suddenly rupturing.

I would like to receive emails from Peebles Media Group (publisher of Envirotec Magazine), including regular newsletters and relevant updates. From time to time this may include sponsored content and messaging from our partners

When calculating the required size for a bund, you must take into account any objects that take up volume within it, such as supports and tank stands, which reduce its effective capacity.

About Blog Resources Careers Contact

Bundingwall

Higher bund walls, with a correspondingly smaller floor area, have the advantage of a more compact, space-saving footprint. Their limiting factor is restricted access for maintenance and space for valves and level sensors.

Spillbunding

Temporary bunds, when moulded from a material like LDPE, have fewer problems as there are no welds or other stress points. However, those designed for transport by forklift may need special reinforcing features to give extra strength and stability.

Temporary or portable bunds can be used around smaller storage vessels, and are made from lighter materials. Bunds for IBCs can be constructed for ease of handling by forklift trucks, and are sometimes referred to as pallet bunds. This type of transportable bund helps to protect against spillage from IBCs or drums during transport, as well as when the container is located on site. IBCs are designed as delivery containers, not as permanent storage tanks, but in reality they are often used for short to medium-term storage on site. Crucially, any IBC used to store a chemical should never be left without a bund.

I would like to receive emails from Peebles Media Group (publisher of Envirotec Magazine), including regular newsletters and relevant updates. From time to time this may include sponsored content and messaging from our partners

Off-site manufactured and modular chemical dosing systems have been growing in popularity, and there have been considerable advances in bund construction and design. For packaged systems up to around 30,000 litres, fabricated PE or PP bunds with a rectangular footprint are now commonplace. However, important design issues need to be addressed if these are to be considered a viable alternative to civil-engineered bunds constructed on-site.

Plastic fabricated bunds must also withstand the rigours of handling. Any bund manufactured off-site will be handled and moved frequently, from its completion in the workshop, through to loading, transportation and installation on site. Although a bund may be designed to form a rigid unit when sitting on a flat base, this rigidity can be compromised when the bund is lifted or moved. Protecting a bund’s integrity during handling may require purpose-made pallets, lifting points or additional fabricated features.

Bunds fall into two broad categories: permanent and temporary. Permanent bunds are either built directly on site or manufactured off-site in a factory and then installed on site. Bunds used to enclose free-standing storage tanks are normally designed into a plant’s layout, taking into account future inspection, cleaning and maintenance requirements.

Any fabricated bund design should include reinforcement bands or added strengthening webs to reduce the load on the welds. As well as protecting welds from high loads at the corners of the bund, external bands stiffen the sidewalls. Without them, many rectangular plastic bunds will bulge when filled with liquid.

Bundingmeaning

With so many variables to consider when choosing appropriate and effective bunding, the simplest and safest option is to buy or hire complete chemical storage and dosing set-ups from a bunding specialist. That way, you get the optimum bunds for your needs, along with all necessary filling and safety systems, all pre-assembled and pre-tested.

Chemical storage bunds are structures that create a leak-proof barrier around an area containing hazardous liquids. The job of a bund is to provide secondary containment if the primary vessel leaks or bursts. By preventing leaking liquids from spreading, the bund gives you time to identify the cause of the leak and to fix it. Bunds can be used on all types of storage tanks, intermediate bulk containers (IBCs) and storage drums. Different bunds are available to suit different applications.