And so, if the flange focal depth is out of whack, the focus marks on your lens will be wrong. When you focus the lens to 6 feet, the camera’s sensor could think it is is 5 feet or 7 feet.

As sensor size increases, the depth of field will decrease for a given aperture (when filling the frame with a subject of the same size and distance). This is because larger sensors require one to get closer to their subject, or to use a longer focal length in order to fill the frame with that subject. This means that one has to use progressively smaller aperture sizes in order to maintain the same depth of field on larger sensors. The following calculator predicts the required aperture and focal length in order to achieve the same depth of field (while maintaining perspective).

Sensor Size Digital SLR with CF of 1.6X Digital SLR with CF of 1.5X Digital SLR with CF of 1.3X Digital SLR with 4/3" sensor 35 mm (full frame) Digital compact with 1/3" sensor Digital compact with 1/2.3" sensor Digital compact with 1/2" sensor Digital compact with 1/1.8" sensor Digital compact with 2/3" sensor Digital compact with a 1" sensor APS 6x4.5 cm 6x6 cm 6x7 cm 5x4 inch 10x8 inch Super35 (3-perf)

On the other hand, exposure times may not necessarily increase as much as one might initially assume, because larger sensors generally have lower noise (and can thus afford to use a higher sensitivity ISO setting while maintaining similar perceived noise).

Depth of field is much shallower for larger format sensors, however one could also use a smaller aperture before reaching the diffraction limit (for your chosen print size and sharpness criteria). So which option has the potential to produce the most detailed photo? Larger sensors (and correspondingly higher pixel counts) undoubtedly produce more detail if you can afford to sacrifice depth of field. On the other hand, if you wish to maintain the same depth of field, larger sensor sizes do not necessarily have a resolution advantage. Furthermore, the diffraction-limited depth of field is the same for all sensor sizes. In other words, if one were to use the smallest aperture before diffraction became significant, all sensor sizes would produce the same depth of field — even though the diffraction limited aperture will be different.

Sensorformat

For studio and test-bench use, the FDC Multi can be powered by its external AC power supply (100-240V AC, 50-80 Hz, 300 mA in — 5V DC, 1.5 A Out). It can also run off a self-contained 3V button battery— useful on location. To save battery power, the FDC Multi has an automatic off function.

To paraphrase David Byrne (from Once in a Lifetime), you may ask yourself, well, why not just use a PL to LPL adapter? You could. But the nagging question is whether that introduces yet another variable into a process where we are looking for micron accuracy. And a dedicated LPL version is easier and faster to use.

CMOSsensor

3. Rotate the FDC’s barrel as if you were focusing a lens. This adjusts the flange focal depth measurement. When the vertical red line appears centered between the two green bars, the actual measured flange focal depth is displayed on the FDC’s scale.

Be warned that both of these terms can be somewhat misleading. The lens focal length does not change just because a lens is used on a different sized sensor — just its angle of view. A 50 mm lens is always a 50 mm lens, regardless of the sensor type. At the same time, "crop factor" may not be appropriate to describe very small sensors because the image is not necessarily cropped out (when using lenses designed for that sensor).

Overall: larger sensors generally provide more control and greater artistic flexibility, but at the cost of requiring larger lenses and more expensive equipment. This flexibility allows one to create a shallower depth of field than possible with a smaller sensor (if desired), but yet still achieve a comparable depth of field to a smaller sensor by using a higher ISO speed and smaller aperture (or when using a tripod).

Another important result is that if depth of field is the limiting factor, the required exposure time increases with sensor size for the same sensitivity. This factor is probably most relevant to macro and nightscape photography. Note that even if photos can be taken handheld in a smaller format, those same photos may not necessarily be taken handheld in the larger format.

If the flange focal depth is off, your monitor will show the red target offset and overlapping one of the green boxes. Rotate the barrel of the FDC multi until the red bar is centered.

Additionally, the optical performance of wide angle lenses is rarely as good as longer focal lengths. Since a cropped sensor is forced to use a wider angle lens to produce the same angle of view as a larger sensor, this can degrade quality. Smaller sensors also enlarge the center region of the lens more, so its resolution limit is likely to be more apparent for lower quality lenses. See the tutorial on camera lens quality for more on this.

An important implication of the above results is that the diffraction-limited pixel size increases for larger sensors (if the depth of field requirements remain the same). This pixel size refers to when the airy disk size becomes the limiting factor in total resolution — not the pixel density. Furthermore, the diffraction-limited depth of field is constant for all sensor sizes. This factor may be critical when deciding on a new camera for your intended use, because more pixels may not necessarily provide more resolution (for your depth of field requirements). In fact, more pixels could even harm image quality by increasing noise and reducing dynamic range (next section).

Larger sensors generally also have larger pixels (although this is not always the case), which give them the potential to produce lower image noise and have a higher dynamic range. Dynamic range describes the range of tones which a sensor can capture below when a pixel becomes completely white, but yet above when texture is indiscernible from background noise (near black). Since larger pixels have a greater volume — and thus a greater range of photon capacity — these generally have a higher dynamic range.

The FDC Multi comes in a small, padded, lockable, water repellent aluminium case. Inside the case, compartments hold accessories such as PL, PV, RF and EF-mount adapters, power supply, and a user manual.

Film and Digital Times is made possible through the generous support of subscribers like you, and with grants from the following companies. Content is in no way linked to sponsorship. We write about the things we use.

This is not always the case however, because the amount of background noise also depends on sensor manufacturing process and how efficiently the camera extracts tonal information from each pixel (without introducing additional noise). In general though, the above trend holds true. Another aspect to consider is that even if two sensors have the same apparent noise when viewed at 100%, the sensor with the higher pixel count will produce a cleaner looking final print. This is because the noise gets enlarged less for the higher pixel count sensor (for a given print size), therefore this noise has a higher frequency and thus appears finer grained.

For SLR cameras, larger sensor sizes result in larger and clearer viewfinder images, which can be especially helpful when manual focusing. However, these will also be heavier and cost more because they require a larger prism/pentamirror to transmit the light from the lens into the viewfinder and towards your eye.

If you’re using a PL mount camera, you have been using the FDC Multi. The Flange Focal Depth of PL mount cameras is 52.00 mm. (At least that is the default setting. Some companies and rental houses may deviate from this standard measurement for a variety of reasons, but that’s another story.)

To begin measuring, attach the FDC Multi onto your camera as you would a lens. The FDC projects a red laser and a pair of green lasers focused at the image plane of the sensor from two different optical axes. If the distance is correct, a vertical red bar aligns— centered evenly—between two green boxes. This is displayed on a monitor connected via the video output of the camera being tested.

The new DENZ FDC Master in LPL mount calibrates the FDC-LPL. A high-resolution black-and-white sensor inside displays a test image and so calibration correction of the FDC can be done by simply adjusting the scale ring.

Sensor #1 Digital SLR with CF of 1.6X Digital SLR with CF of 1.5X Digital SLR with CF of 1.3X Digital SLR with 4/3" sensor 35 mm (full frame) Digital compact with 1/3" sensor Digital compact with 1/2.3" sensor Digital compact with 1/2" sensor Digital compact with 1/1.8" sensor Digital compact with 2/3" sensor Digital compact with a 1" sensor APS 6x4.5 cm 6x6 cm 6x7 cm 5x4 inch 10x8 inch Super35 (3-perf)

Camera sensorstructure

One can understand this by looking at how manufacturers make their digital sensors. Each sensor is cut from a larger sheet of silicon material called a wafer, which may contain thousands of individual chips. Each wafer is extremely expensive (thousands of dollars), therefore fewer chips per wafer result in a much higher cost per chip. Furthermore, the chance of an irreparable defect (too many hot pixels or otherwise) ending up in a given sensor increases with sensor area, therefore the percentage of usable sensors goes down with increasing sensor area (yield per wafer). Assuming these factors (chips per wafer and yield) are most important, costs increase proportional to the square of sensor area (a sensor 2X as big costs 4X as much). Real-world manufacturing has a more complicated size versus cost relationship, but this gives you an idea of skyrocketing costs.

Use the following calculator to estimate when diffraction begins to reduce sharpness. Note that this only shows when diffraction will be visible when viewed onscreen at 100% — whether this will be apparent in the final print also depends on viewing distance and print size. To calculate this as well, please visit: diffraction limits and photography.

No matter what the pixel size, larger sensors unavoidably have more light-gathering area. Theoretically, a larger sensor with smaller pixels will still have lower apparent noise (for a given print size) than a smaller sensor with larger pixels (and a resulting much lower total pixel count). This is because noise in the higher resolution camera gets enlarged less, even if it may look noisier at 100% on your computer screen. Alternatively, one could conceivably average adjacent pixels in the higher pixel count sensor (thereby reducing random noise) while still achieving the resolution of the lower pixel count sensor. This is why images downsized for the web and small prints look so noise-free.

Some lenses are only available for certain sensor sizes (or may not work as intended otherwise), which might also be a consideration if these help your style of photography. One notable type is tilt/shift lenses, which allow one to increase (or decrease) the apparent depth of field using the tilt feature. Tilt/shift lenses can also use shift to control perspective and reduce (or eliminate) converging vertical lines caused by aiming the camera above or below the horizon (useful in architectural photography). Furthermore, fast ultra-wide angle lenses (f/2.8 or larger) aren't as common for cropped sensors, which may be a deciding factor if needed in sports or photojournalism.

Camera phones and other compact cameras use sensor sizes in the range of ~1/4" to 2/3". Olympus, Fuji and Kodak all teamed up to create a standard 4/3 system, which has a 2X crop factor compared to 35 mm film. Medium format and larger sensors exist, however these are far less common and currently prohibitively expensive. These will thus not be addressed here specifically, but the same principles still apply.

Keep in mind that the onset of diffraction is gradual, so apertures slightly larger or smaller than the above diffraction limit will not all of a sudden look better or worse, respectively. Furthermore, the above is only a theoretical limit; actual results will also depend on lens characteristics. The following diagrams show the size of the airy disk (theoretical maximum resolving ability) for two apertures against a grid representing pixel size:

Sensor Type Digital SLR with CF of 1.6X Digital SLR with CF of 1.5X Digital SLR with CF of 1.3X Digital SLR with 4/3" sensor 35 mm (full frame) Digital compact with 1/3" sensor Digital compact with 1/2.3" sensor Digital compact with 1/2" sensor Digital compact with 1/1.8" sensor Digital compact with 2/3" sensor Digital compact with a 1" sensor APS 6x4.5 cm 6x6 cm 6x7 cm 5x4 inch 10x8 inch Super35 (3-perf)

Ideally, perceived noise levels (at a given print size) generally decrease with larger digital camera sensors (regardless of pixel size).

1. Flange focal depth (FFD), sometimes shorted to “Flange depth,” is the depth of the camera cavity from the camera’s mount to the sensor.

An implication of this is that if one requires the subject to occupy the same fraction of the image on a 35 mm camera as using a 200 mm f/2.8 lens on a camera with a 1.5X crop factor (requiring a 300 mm f/2.8 lens), one would have to carry 3.5X as much weight! This also ignores the size difference between the two, which may be important if one does not want to draw attention in public. Additionally, heavier lenses typically cost much more.

One might initially think that throwing away image information is never ideal, however it does have its advantages. Nearly all lenses are sharpest at their centers, while quality degrades progressively toward to the edges. This means that a cropped sensor effectively discards the lowest quality portions of the image, which is quite useful when using low quality lenses (as these typically have the worst edge quality).

Smaller sensors require lighter lenses (for equivalent angle of view, zoom range, build quality and aperture range). This difference may be critical for wildlife, hiking and travel photography because all of these often utilize heavier lenses or require carrying equipment for extended periods of time. The chart below illustrates this trend for a selection of Canon telephoto lenses typical in sport and wildlife photography:

Furthermore, larger pixels receive a greater flux of photons during a given exposure time (at the same f-stop), so their light signal is much stronger. For a given amount of background noise, this produces a higher signal to noise ratio — and thus a smoother looking photo.

The cost of a digital sensor rises dramatically as its area increases. This means that a sensor with twice the area will cost more than twice as much, so you are effectively paying more per unit "sensor real estate" as you move to larger sizes.

In the prehistoric analog days of film, just a few years ago, you checked flange focal depth by poking a pointy-tipped tool—a dial with a probe—appropriately named a depth gauge. The big difference now is that with digital cameras you risk scratching the low-pass filter covering the sensor. Also, few digital cameras use the same sensor, low pass filter or cover glass and the cover glass is not the image plane. The sensor, with its photosites, is the image plane.

Just as analog depth gauges for film cameras are zeroed out and calibrated using a metal collar, DENZ FDC Multi testers can be checked on a DENZ FDC Master.

Understanding CMOS imagesensor

This article aims to address the question: how does your digital camera's sensor size influence different types of photography? Your choice of sensor size is analogous to choosing between 35 mm, medium format and large format film cameras — with a few notable differences unique to digital technology. Much confusion often arises on this topic because there are both so many different size options, and so many trade-offs relating to depth of field, image noise, diffraction, cost and size/weight.

The new DENZ FDC-LPL Multi tool is the latest addition to their line of essential Focal Depth Controllers, joining the FDC Multi which comes in PL mount and a variety of adapters. If you build, buy, rent or use LPL mount  cameras, you need this testing device.

As an example calculation, if one wanted to reproduce the same perspective and depth of field on a full frame sensor as that attained using a 10 mm lens at f/11 on a camera with a 1.6X crop factor, one would need to use a 16 mm lens and an aperture of roughly f/18. Alternatively, if one used a 50 mm f/1.4 lens on a full frame sensor, this would produce a depth of field so shallow it would require an aperture of 0.9 on a camera with a 1.6X crop factor — not possible with consumer lenses!

Note that the above calculator assumes that you have a lens on the new sensor (#2) which can reproduce the same angle of view as on the original sensor (#1). If you instead use the same lens, then the aperture requirements remain the same (but you will have to get closer to your subject). This option, however, also changes perspective.

Larger sensor sizes can use smaller apertures before the diffraction airy disk becomes larger than the circle of confusion (determined by print size and sharpness criteria). This is primarily because larger sensors do not have to be enlarged as much in order to achieve the same print size. As an example: one could theoretically use a digital sensor as large as 8x10 inches, and so its image would not need to be enlarged at all for a 8x10 inch print, whereas a 35 mm sensor would require significant enlargement.

Sensor #2 Digital SLR with CF of 1.6X Digital SLR with CF of 1.5X Digital SLR with CF of 1.3X Digital SLR with 4/3" sensor 35 mm (full frame) Digital compact with 1/3" sensor Digital compact with 1/2.3" sensor Digital compact with 1/2" sensor Digital compact with 1/1.8" sensor Digital compact with 2/3" sensor Digital compact with a 1" sensor APS 6x4.5 cm 6x6 cm 6x7 cm 5x4 inch 10x8 inch Super35 (3-perf)

And that is why the DENZ FDC-LPL and its sister FDC Multi are considered industry standards. Major manufacturers such as ARRI, RED, Blackmagic Design, Vision Research and others have been using the DENZ FDC for years to check the depth of their cameras during assembly. Many rental houses check their cameras with the FDC and busy camera assistants carry them in their kits.

A shallower depth of field may be desirable for portraits because it improves background blur, whereas a larger depth of field is desirable for landscape photography. This is why compact cameras struggle to produce significant background blur in portraits, while large format cameras struggle to produce adequate depth of field in landscapes.

Camera sensor

Next, read the amount of correction on the barrel’s scale. Each witness mark line represents 0.01 mm (10 microns). For example, if it shows 2 witness marks on the Minus (-) side,  that means you are -0.02 mm short of optimal 52.00 mm.

Similarly, the focal length multiplier relates the focal length of a lens used on a smaller format to a 35 mm lens producing an equivalent angle of view, and is equal to the crop factor. This means that a 50 mm lens used on a sensor with a 1.6X crop factor would produce the same field of view as a 1.6 x 50 = 80 mm lens on a 35 mm full frame sensor.

The crop factor is the sensor's diagonal size compared to a full-frame 35 mm sensor. It is called this because when using a 35 mm lens, such a sensor effectively crops out this much of the image at its exterior (due to its limited size).

This is not to say though that certain sized sensors will always be prohibitively expensive; their price may eventually drop, but the relative cost of a larger sensor is likely to remain significantly more expensive (per unit area) when compared to some smaller size.

Canon's 1Ds/5D and Nikon D3 series are the most common full frame sensors. Canon cameras such as the Rebel/60D/7D all have a 1.6X crop factor, whereas mainstream Nikon SLR cameras have a 1.5X crop factor. The above chart excludes the 1.3X crop factor, which is used in Canon's 1D series cameras.

Why? Flange focal depth (FFD) is the distance from the shiny metal flange of the camera’s lens mount to the imaging sensor. This distance can vary with (gasp) manufacturing tolerance errors, wear-and-tear on location, temperature, shipping and age. An unsupported heavy lens can weigh heavily on the mount. A bumpy and crazy car chase could cause problems, most likely not on a solid-as-a-rock ARRI, but you never know.

Sensor sizes currently have many possibilities, depending on their use, price point and desired portability. The relative size for many of these is shown below:

When the flange focal depth of the camera is correct—e.g. 52.00 mm for a PL mount camera, the FDC-PL measuring scale’s red “52” witness mark will line up with the red index mark. On the FDC-LPL, it will line up at 42.00 mm. This means that no correction is necessary.

On the other hand, this also means that one is carrying a much larger lens than is necessary — a factor particularly relevant to those carrying their camera for extended periods of time (see section below). Ideally, one would use nearly all image light transmitted from the lens, and this lens would be of high enough quality that its change in sharpness would be negligible towards its edges.

The remedy is to adjust the flange focal depth of the camera by removing the camera’s lens mount and adding a 0.02 mm shim under the camera mount. Similarly, if the FDC multi shows a Plus (+) reading, you remove shims. Tedious trial and error procedures are a thing of the past because the FDC tells you exactly how many shims to add or remove.