Lens Material Properties - optical lens glass

 2024-11-12 23:41:09

surface quality 60-40

6.3.1 Scratch and dig identification. - This is specified by two letters separated by a hyphen (i.e. F-F). The first letter of the pair is the maximum scratch letter. The second letter is the maximum dig letter.

Are you looking for Bolle Ransom Sports Polarizad 11695 Sunglasses? At trekkinn you will find all types of Sunglasses products from the best brands. For example from Bolle, a leading brand in the industry and guarantees you the best manufacturing quality. Do not wait any longer and equip yourself with products from our outdoor store.

Tradeinn Retail Services as the data controller will process your data in order to manage registered users on our website and process your order, as well as the sending of advertising related to the products and services. You can access, rectify and delete your data, as well as exercise other rights by consulting the additional and detailed information on data protection in our Privacy Policy.

mil-c-675

An email has been sent to the provided E-mail address. Make sure you check your Spam email folder just in case your email service provider has redirected it there.

iso 10110-7

The cheesecloth pad shall completely cover the eraser portion of the tester and be secured to the shaft with an elastic band. The cheesecloth pad shall be rubbed across the coated surface from one point to another over the same path for 25 complete cycles (50 strokes) with a minimum force of 1.0 pound (0.45kg) continuously applied. The length of the stroke shall be approximately equal to two widths of the cheesecloth pad when the diameter of the area of the component permits.

80 50 scratch-dig

Within one hour after the humidity test of 4.6.8.2 the coated component, or witness piece, shall be subjected to a moderate abrasion be rubbing the coated surface with a 1/4 inch (6.4mm) thick by 3/4 inch (9.5mm) wide pad of clean dry, laundered cheesecloth conforming to CCC-C-440 affixed to an abrasion tester that conforms to drawing D7680606.

3.4.1.2 Scratches. - Surface scratches (coating and substrate) shall not be in excess of the values specified on the component drawing or procurement document (See 6.2f). Scratches are permissible provided the width does not exceed that specified by the scratch letter. The accumulated length of all maximum scratches shall not exceed 1/4 of the average diameter of the element, The scratch letter and corresponding width are shown in Table I.

The coated component, or witness piece, shall be placed into an environmental controlled test chamber and exposed to a temperature of +120° +/-4°F (49° +/-2°C) and 95% to 100% relative humidity for a minimum of 24 hours. Subsequent to this exposure the coated component, or witness piece, shall be removed from the test chamber, cleaned (see 4.6.1), dried, and then subjected to the examinations specified in 4.6.7.1 and 4.6.7.3. The coating shall conform to the requirements of 3.4.2.1.2. The coated component, or witness piece, shall then be subjected to the test specified in 4.6.8.3.

The optical coating industry has adopted the US Military Specifications (often referred to as “MIL specs”) as a standard for testing the mechanical properties of coatings. All NOC coatings are adhesion tested and inspected for surface quality to the grade required by the customer. At NOC we can also test against humidity, abrasion and other MIL specs as necessary.

I have read and accept the conditions contained in the Privacy Policy on processing of my data to send me the newsletter

mil-c-48497

The question has already been answered, thank you very much for trying to help another customer. We will count on you for future questions.

Tradeinn Retail Services as the data controller will process your data in order to respond to your query or request. You can access, rectify and delete your data, as well as exercise other rights by consulting the additional and detailed information on data protection in our Privacy Policy.

iso 10110-7 pdf

C7641866

An email has been sent to the provided E-mail address. Make sure you check your Spam email folder just in case your email service provider has redirected it there.

3.4.1.3 Digs. - Surface digs (coating and substrate) shall not be in excess of the values specified on the component drawing or procurement document (See 6.2g). Digs are permissible on a surface provided the average diameter does not exceed that specified by the dig letter and no more than (1) maximum size dig occurs in any 20mm (0.8”) diameter circle on the substrate. The dig letter and corresponding average diameter are shown in Table II.

The coated component, or witness piece, shall be subjected to an adhesion test using 1/2" (12.7 mm) wide cellophane tape conforming to type I of L-T-90. Press the adhesive surface of the cellophane tape firmly against the coated surface so as to cover the stained area, then quickly remove it at an angle which is normal to the coated surface. Immediately following the removal of the adhesive tape, the coated surface of the component, or witness piece, shall be examined by reflection using the inspection technique specified in 4.6.4. The coating shall conform to the requirements of 3.4.2.1.1. Subsequent to this test the coated component, or witness piece, shall be subjected to the test in 4.6.8.2.

Your feedback is important to us, your review about this product will be revised by our experts and will be published within 5 working days. Please make sure that your review focus on the product and your experience with it, this will help other customers make more confident decisions. For any issues with an order, please contact us.

The coated substrate shall be examined for scratches and digs by reflection or transmission, as applicable, using the inspection technique specified in 4.6.4. Magnification shall be used as needed in these examinations. The length and width of scratches, and the dig (hole) diameters shall be determined by use of interferometer, microscopic measuring devices, calibrated precision comparators, or similar applicable precision measuring devices. The width, length and density of all scratches in the coating or substrate shall conform to the requirements of 3.4.1.2 and 3.4.1.2.1. The diameter and density of all digs (holes) in the coating or substrate shall conform to the requirements of 3.4.1.3 and 3.4.1.3.1.

YOUR SUBSCRIPTION HAS BEEN CONFIRMEDThank you very much for subscribing. You already have everything ready to receive exclusive offers and news that will make your day.See you soon

The abrasion tester shall be held approximately normal to the surface under test during the rubbing operation. Subsequent to the rubbing operation the component, or witness piece, shall be cleaned (see 4.6.1), dried and then subjected to an examination by reflection using the inspection technique specified in 4.6.4 for evidence of physical damage to the coating. The coating on the component, or witness piece, shall meet the requirements of 3.4.2.1.3.

mil-prf-13830b pdf

We have a wide range of filters available for purchase through our online catalogue. If you cant find the product you need, please click here to contact us and discuss bespoke orders.

Tradeinn Retail Services as the data controller will process your data for the purpose of sending you our commercial newsletters about our services and products. You can access, rectify and delete your data, as well as exercise other rights by consulting the additional and detailed information on data protection in our Privacy Policy.

News