High-contrast resolution is the ability to detect finely spaced lines or holes with whose signals differ considerably from background. Low-contrast resolution ...

cause to divide into conflicting or contrasting positions.

(2) A probation officer or peace officer, upon request of the chief probation officer or otherwise having probable cause to believe that the defendant has failed to comply with a requirement imposed as a condition of the order or that he has committed another offense, may arrest him without a warrant;

With your New Way product directly placed on a precision ground surface, parallelism shall be measured by use of a displacement gauge, mounted to an armature and free to slide on the precision ground surface to which your bearing or air bar is mounted. If the bearing or air bar must be elevated, it shall be placed on precision gage blocks, with a graded tolerance. Zero the gauge against one corner of the surface which is parallel with your guide surface. Take measurements along this surface, paying special attention to measurements at the corners of the air bar surface. The largest difference between measured values is the parallelism between your bearing and the guide surface.

New Way Air Bearings’ products provide exceptional flatness and parallelism, but in order to achieve the specifications listed on our product pages, all New Way products must be placed directly against a precision ground guide surface. Before any measurements are taken, the surfaces should be cleaned in accordance with our Care and Air guidelines, namely using 70% isopropyl alcohol only.

You're all set! You already receive all suggested Justia Opinion Summary Newsletters. You can explore additional available newsletters here.

b. When the court revokes a suspension or probation, it may impose on the defendant any sentence that might have been imposed originally for the offense of which he was convicted.

2C:45-3. a. At any time before the discharge of the defendant or the termination of the period of suspension or probation:

(3) The court, if there is probable cause to believe that the defendant has committed another offense or if he has been held to answer therefor, may commit him without bail, pending a determination of the charge by the court having jurisdiction thereof;

Microsoft Skype for Business Standard Edition, 2015 - 2019, Supported. Collaborate. Optimize the collaboration that connects your people. Collaborate. IR's ...

2C:45-3 Summons or arrest of defendant under suspended sentence or on probation; commitment without bail; revocation and resentence.

The idea behind a magnifying glass is to make something look bigger, but how does this work? Well, the principle is so simple you probably already know it ...

by T Tools — Perfluorinated graded-index polymer optical fibers (GI-POFs) combine high data transmission rates and low attenuation in the.

Hex Key · Hex Key. Print Page. T4411 15. HEXAGON KEY, 15MM. CK TOOLS T4411 15. Image is for illustrative purposes only. Please refer to product description ...

(4) The court, if satisfied that the defendant has inexcusably failed to comply with a substantial requirement imposed as a condition of the order or if he has been convicted of another offense, may revoke the suspension or probation and sentence or resentence the defendant, as provided in this section. No revocation of suspension or probation shall be based on: (a) failure to pay a fine or make restitution, unless the failure was willful; or (b) manufacturing, distributing, or dispensing, or possessing or having under control with intent to manufacture, distribute, or dispense, marijuana or hashish in violation of paragraph (12) of subsection b. of N.J.S.2C:35-5, or possession of marijuana or hashish in violation of paragraph (3) of subsection a. of N.J.S.2C:35-10.

Per our Application and Design Guide, we recommend a surface finish of 16 RMS or better. Local flatness, which we define as the flatness under the bearing at any one time, should always remain below 50% of the designed air gap. This is a worst case scenario, and it is relatively easy to stay within 10% of the air gap height.

Fresnel Lens · With two people, hold the giant Fresnel lens with the ridged side facing up towards the sun. On a bright day you should see a bright focal spot ...

2022610 — An anti-reflective coat is a layer applied to glasses to improve your vision, reduce glare, and eye strain, and improve the appearance.

c. The commencement of a probation revocation proceeding shall toll the probationary period until termination of such proceedings. In the event that the court does not find a violation of probation, this subsection shall not operate to toll the probationary period.

The largest selection of calibrated laser power sensors for measurement from 0.3 nW up to 100000 W. State-of-the-art thermopile, photodiode and pyroelectric ...

Mar 6, 2019 — The lensmaker's equation, 1p+1q=1f is all you need if you have p and q. Just solve it for f, which is the focal length (the distance from the ...

Bearing height shall be measured with your height gage placed directly on the precision ground surface to which the bearing or conveyor bar is mounted. With the bearing leveled in accordance with our Application and Design Guide, zero your height gage against the top surface of the mounting block, and then lower the probe tip onto the upper surface of the air bar. Dimensioning of an air bar’s thickness can also be accomplished through use of a micrometer, placing the micrometer anvil face and spindle on opposite sides of the bearing, and measuring the distance between them.

Flatness shall be measured by use of a displacement gauge, mounted to an armature and free to slide on the precision ground surface to which your bearing or air bar is mounted. Zero the gauge against one end of the surface for which you wish to measure flatness, and then take measurements in regular intervals along the surface. The largest difference between measured values represents the flatness of the component. Of note, the air bar, air bearing or other component must be placed directly upon a precision ground surface and parallel with the guide surface in order to take accurate measurements on flatness deviations of the bearing surface.