The spot size of a laser beam cutter ranges from 15 μm to 170 μm (0.003 to 0.007 inches), depending on the lens you are mounting.

Laser emitters select a specific wavelength of light inside an amplification medium contained in a resonating optical cavity. The light gets amplified by repeatedly bouncing back and forth between two mirrors on the two sides of the cavity, traveling through the energized medium. One of the mirrors on the resonator side is partially transparent and allows the amplified wavelength to escape the camber.

Laser beams propagate following — ideally — the equation of a Gaussian beam, where the amplitude envelope follows the Gaussian function, with a smooth peak in the center, surrounded by decreasing tails.

Let's consider an example. We will study a green laser with wavelength 532 nm532\ \text{nm}532 nm, slightly deviating from a Gaussian beam: the quality parameter is M=1.12M=1.12M=1.12. Assume it reaches a lens with focal length 5 cm5\ \text{cm}5 cm with a diameter of 0.5 mm0.5\ \text{mm}0.5 mm.

One of the uses of collimated laser beams is optic fiber communication. A well-collimated laser can propagate for long distances in the "comfortable" medium of fibers, only needing some amplification on the way.

This equation is straightforward with its implications. The size of the beam spot is directly proportional to the lens's focal length. A shorter focal length makes for a highly focused beam. However, there's a tradeoff: the more focused the beam is, the higher its divergence, and in a short distance past the focal length, the beam would lose its laser properties.

Physicist by education, scientist by vocation. He holds a master’s degree in complex systems physics with a specialization in quantum technologies. If he is not reading something, he is outdoors trying to enjoy every bit of nature around him. He uses his memory as an advantage, and everything you will read from him contains at least one “I read about this five years ago” moment! See full profile

Our laser beam spot size calculator will give you the answer to your problems at the speed of light. You only have to provide us with the numbers of the parameters you know, and we will calculate the result for both the laser beam spot size and the depth of focus.

An ideal Gaussian beam has the smallest possible spot size, thus preventing M² from assuming values smaller than 1. The spot size S increases with M² for any other value.

Lasers are widely used in many fields, from entertainment to medicine, from the military to advanced scientific research. Saying that they lighted the way to see the world with different eyes is not an understatement.

We are now in the last part of our diagram. The collimated beans reach a lens with focal length(learn what is this quantity with out focal length calculator) fff that focuses the beam in a single, small spot with diameter SSS. We created a new Gaussian beam with all the characteristics of the previous one, just different values. In particular, we have a new waist.

The effect of the laser beam quality on the spot size is directly related to a deviation from the ideality of the beam. The ideal value of M² is 1, which corresponds to an ideal Gaussian beam.

Right after their emission, laser beams diverge. We talked about this in detail in our laser divergence calculator. Even though the beam is more collimated than one of the other light sources (light bulbs, to name one), thanks to the coherency of the beam, this doesn't prevent the beam spot from spreading after a certain distance.

Physicists decided to quantify this loss of focus through an appositely set quantity called the Rayleigh range: the distance from the waist (or any focusing point) at which the beam spot size doubles its area (which corresponds to an increase of 2\sqrt{2}2​ of the diameter). A laser beam's depth of focus corresponds to twice the Rayleigh range: when we move past this distance, the laser loses its sharpness and coherence.

To calculate the spot size of a laser beam, you need to know the setup of your optical system. Be sure to know the following:

The name LASER is the acronym for "light amplification by stimulated emission of radiation", which describes the principal characteristic of the device itself: by pumping a medium where a specific light frequency may appear, we obtain the amplification of such frequency and subsequent emission.

The beam quality parameter M2M^2M2 is a measure of how much a laser beam deviates from the ideal Gaussian beam (which corresponds to M2=1M^2=1M2=1).

You can increase the depth of focus (hence maintaining a high quality of the beam for a longer distance) by lengthening the lens's focal length. However, as you can see in our calculator, this is detrimental to the size of the spot (which increases).

🙋 Find out more about lasers with our other dedicated tools: the laser brightness calculator and the laser linewidth and bandwidth calculator.

Learn how to calculate the spot size of a laser beam with our dedicated tool. Initially, it can look complex, but we will guide you through a detailed explanation of the physics of the problem, teach you how to calculate the laser beam spot size after introducing all the necessary quantities, and end the article with some practical examples.

Physicist holding a 1st class degree and a member of the Institute of Physics. Creator of the UK vaccine queue calculator, and featured in many publications, including The Sun, Daily Mail, Express, and Independent. Tenacious in researching answers to questions and has an affection for coding. Hobbies include cycling, walking, and birdwatching. You can find him on Twitter @OmniSteve. See full profile

🙋 If you input the correct combination of parameters, you can use our tool in reverse. For example, to find the right lens to achieve a specified spot size.

After reaching the focus, the laser beam gets wider, losing its small beam spot size and progressively resembling a "normal" source of light.

When necessary, it's typical to collimate the laser beam through a lens that collects the weakly divergent rays coming from the optical resonator and straightens them, allowing for a longer coherence distance.

In the diagram below, you can see the path of a laser beam from the emission to its focusing on a small spot. On the left, we find the emitter, followed by the collimating lens that corrects the divergence. Let's check these first steps.

When the laser beam reaches its destination, you may want to focus it, concentrating its power in a small spot. Think of laser cutters, mainly, but also the standard pointers. A lens is often included to keep the divergence at bay. How small can we focus our beam?

The shorter the focal length of the lens, the smaller the spot, which allows for the engraving of finer details. However, smaller spots are not suitable for working with thick materials.

Lasers are sources of coherent light, which means that the light waves are in phase over a certain distance (the coherence length), thus maintaining their focus and small beam size.

The Rayleigh range is the distance from the waist at which a laser beam's area becomes twice its minimum value. At a distance of two times the Rayleigh range, the sharpness of the beam is insufficient to operate the laser (for imaging, cutting, etc.). The Rayleigh range is closely related to the divergence of a beam.