When reading an exposure meter, the device will display the aperture, shutter speed, and ISO settings needed to obtain optimal exposure for a given scene.

Knowing not only when to use the light meter, but choosing the right kind, is essential because sometimes, in-camera TTL light metering isn’t accurate enough. Environments with multiple light sources and subjects with both deep shadow and bright highlights should be measured using a handheld light meter.

Thanks to the light meter and exposure adjustments you choose in response, poor illumination should be a thing of the past! Exposure is a fundamental photography basic and I go into this in even greater detail in my Exposure in Photography guide!

Light metering and exposure go hand in hand. By measuring one, you’ll better understand how each aspect of the exposure triangle (aperture, shutter speed, ISO) affects your image. If you know how to use the light meter, you can maximize image quality in-camera. You’ll also save time in post-processing since you may not even need to make too many adjustments.

Medium pressure ultraviolet light bulbs emit broadband UVB/UVC wavelengths. These are a type of high-intensity discharge (HID) lamp. Because of the UVB component, they tend to produce more damage to enzymes of microbes and inhibit photoreactivation.

Matrix/Evaluative/Multi metering is used when you want to optimize good exposure for the entire scene. The camera breaks up the scene into sections and averages the exposure settings to ensure there is a balance between highlights and shadows.

We carry ultraviolet light bulbs using all of these wavelengths for a variety of stage/studio, special effects, phototherapy, and air/water purification equipment. If you can not find the ultraviolet bulb you need, call 800.784.1998 to speak with a lighting specialist. In most cases, we can help you locate the UV bulb you are looking for.

Another use of light meters is finding which aspects of a scene or subject are the most intensely illuminated. If there are drastic changes in light intensity within the scene, choosing the right light metering mode will be the difference between a properly exposed subject and a poor photograph.

In retrospect, light meters in film cameras were extremely important because you risked wasting film if the exposure settings were off. While the near-limitless capacity of digital technology is more forgiving, incident light metering still has a place in genres where moments can’t be easily repeated and timing is crucial, like wedding and event photography.

BestUVlight Sanitizerforhome

All of the bulbs and fixtures in this category emit light in the ultraviolet part of the spectrum. However, not all UV bulbs or fixtures are interchangeable. There are a large number of applications utilizing UV light.

Each type of light metering is defined by where the light meter is placed. Most photographers today use the exposure meter in the camera rather than a separate handheld device. However, handheld light meters are extremely important in some cases as we’ll see below.

Using center-weighted metering, the camera places the most importance on the center for light metering. The corners of the frame aren’t used for exposure metering, making this perfect for portraits and other styles where you’ll be using most of the center of the frame.

In short, light metering can be defined as the process of measuring the light of a scene before taking a picture. This process is done using a light meter or exposure meter.

Knowing how to use the light meter relies on understanding the interplay of shutter speed, ISO, and aperture. By reading the exposure meter in camera you can adjust each of these values until your eyes and the light meter both agree, or you can directly help your camera do it for you if you shoot in automatic mode.

Now, we’ll be discussing how to use the in-camera light meter and differentiating between each type of in-camera metering. Lastly, I’ll explain light meter readings and what to do with the information received from them!

UVlight Lampforplants

Remember that light metering in Nikon vs Canon and other brands may use different terms. Consult your user manual and camera menus to determine precisely which metering mode will be best for each occasion.

UV-A light provides very little disinfection power, although it can have some germicidal effectiveness over very long periods of time. It is generally not dangerous to humans, except in high dosage amounts.

UV-C light can be extremely harmful to human and animal skin and eyes, and is used for disinfection of air and surfaces, as well as water purification. Most UV-C light from the sun is filtered out before it even hits the earth.

From there, it’s much easier to understand each of the main types of in-camera light metering: Matrix/Evaluative, Center-Weighted, and Spot Metering. It’s also important to remember how to find and read the exposure meter in-camera, which provides straightforward, valuable information even if you think you have the right settings in place.

First, the camera takes in light reflecting off of the subject through the lens (TTL). Then, the built-in exposure meter informs you as to whether the image is underexposed (not enough light), well exposed, or overexposed (too much light).

In both cases, if you shoot in auto or manual mode, using the exposure meter correctly is essential to get correctly exposed photos.

I feel metering is very important and tricky to expose proper picture. What people fail to understand is where exactly in the frame metering should be measured, example: do I take metering in the highlight area ? So that that particular portion / part ( portrait) not over exposed / not burnt..!!??

Hi Garani, thanks for your words. Yes, it’s usually better to take the metering in the highlight area. My advice is to always check your histogram, no matter what metering you’re using. It’s always easier to recover the shadows than the highlights later in post-processing.

UVlight Bulb

Each of these metering modes are also discussed in greater detail and with plenty of examples in our guide to Metering Modes in Photography:

The most common type of UV light bulb is the low pressure mercury lamp. These resemble fluorescent tubes or compact fluorescent bulbs. For UVC, they are made of quartz with a peak transmission of 253.7nm. UVB and UVA bulbs are more similar to fluorescent tubes, using glass with various phosphors to control the wavelengths emitted. They offer the lowest cost, good energy efficiency, and long life of 9,000-17,000 hours. There are also more manufacturers making these bulbs, and more variations of the bulbs in terms of lengths, wattages, bases, and bulb shapes.

Cameras with built-in light meters, like all modern digital cameras, use reflective light metering. This is usually more than accurate enough but sometimes the light meter can be confused by abrupt shifts in light absorption within the scene. One example is reflective light metering off of the white dress of a bride only to find that the dark suit of the groom is underexposed.

Light metering in digital photography isn’t too difficult to grasp, and understanding how light metering in camera works will go a long way in improving your work as a photographer.

What is Light Metering? Light metering is the process of using either an in-camera system or handheld device to measure light and suggest the best settings. Aperture, shutter speed, and ISO are the three settings of the exposure triangle that can be adjusted for good exposure after the light metering process. What is an Exposure Meter? The exposure meter is a gauge shown in the Electronic/Optical viewfinder or LCD screen that tells you how well-exposed your image will be. By referencing the exposure meter, you’ll know if you need to make adjustments to the light metering mode, available light, or exposure settings. What is a Light Meter on a Camera? The light meter on a camera uses reflective light metering to sense lighting bouncing from your subject through the lens. This is also called TTL light metering. How do You Read a Light Meter? Once the light meter makes a measurement, it will provide an exposure value according to your settings and light metering mode. After considering this, you can adjust the aperture, shutter speed, and ISO value for the subject or scene. If you’re using an in-camera meter and using a semi-automatic or fully automatic mode, the camera will select the proper exposure values. If using a handheld meter, you’ll need to set each value using Manual mode.

UVLight walmart

The TTL light metering system also helps the camera gauge how much exposure to provide if you’re using a flash setup. In short, using the light meter in photography is the best way to get good exposure and minimize the amount of time spent in post-processing.

Once the light meter makes a measurement, it will provide an exposure value according to your settings and light metering mode. After considering this, you can adjust the aperture, shutter speed, and ISO value for the subject or scene. If you’re using an in-camera meter and using a semi-automatic or fully automatic mode, the camera will select the proper exposure values. If using a handheld meter, you’ll need to set each value using Manual mode.

Without understanding the exposure meter, you’re liable to end up with blown highlights, crushed shadows, high digital noise, and other elements. This might result in a wrong histogram that can be hard to fix in post. Still, if you do find issues like digital noise arising, there are different ways to fix it, which I share in my Noise in Photography article.

UVlight Torch

When using spot metering, the system measures light using a single focus point instead of sections of the image frame. Spot metering is used when a single element within the frame is especially important, or with backlit subjects.

Reflective light metering is what your camera uses to measure available light. Simply put, the camera meters by judging exposure based on light reflected from the subject.

The light meter on a camera uses reflective light metering to sense lighting bouncing from your subject through the lens. This is also called TTL light metering.

LEDs that emit ultraviolet light are currently more expensive than standard LEDs, but hold promise for applications where fluorescent tube-type lamps are inconvenient or unavailable. LEDs have a greater energy efficiency than other UV light sources and can be developed to emit radiation at various wavelengths. Blacklight LEDs are available in various sizes and bases, and some air and water disinfection fixtures that use UVC LEDs have been developed. UV LEDs have also been used to treat a range of skin disorders and wound healing.

UVLight LampforNails

UV pulsed xenon lamps emit pulses of ultraviolet light lasting a few milliseconds. They often have very high wattages and high ultraviolet outputs. They emit a broad spectrum of light in the UV, visible, and infrared ranges. They have been found to be as effective as mercury lamps in germicidal effectiveness.

The importance of light metering lies in getting the right exposure in-camera. Proper exposure forms the basis for capturing the image with the most complete information in the highlights and shadows and with the maximum color detail.

In order to understand how to use the light meter, it’s fundamental to be familiar not only with what light metering is, but also with the different types of light meters (TTL and handheld).

Light metering is fundamental because it helps the camera know precisely where and how to look at the light within the frame. Without understanding light metering in photography, you can end up with a poorly exposed image even if there is plenty of light to work with.

The UV-A part of the ultraviolet spectrum is used in a wide variety of applications. Commonly referred to as blacklights, these UV bulbs are much more than a novelty. Although they are used in many blacklight fixtures in stage/studio applications, blacklights can be used for fraud detection of currency, validation of identification, and even identifying organic waste to track the path of bedbugs.

UV-A light bulbs are often found in insect traps and bug zappers for commercial and residential applications. Many flying insects are attracted to ultraviolet light.

Ultraviolet light (UV) is invisible to the human eye. It is part of the electromagnetic spectrum that lies beyond the purple range of the visible spectrum. The ultraviolet spectrum has wavelengths between 100 and 400 nanometers (nm). The UV spectrum is further divided into wavelength ranges named UVA (blacklight), UVB (phototherapy), and UVC (germicidal).

Specialty UV-B bulbs are used in medical settings for treatment of jaundice, skin disorders, and other conditions. It can also be used for some germicidal applications, although it does not have nearly the effective power of UV-C lights.

Maybe you have more questions on exposure after reading this light metering in photography guide. In that case, take a look at my Exposure in Photography guide, which discusses each aspect of the Exposure Triangle in greater detail!

When the gauge indicates a negative exposure value (EV), the camera light meter is sensing that the subject or resulting image will be underexposed and vice versa. You should be aiming for as close to the center of the axis or 0 as possible.

A digital camera light meter uses a reflective metering design to gauge exposure. Usually, the light meter is activated either constantly when the camera is on or with a half-press of the shutter.

Handheld light meters are also useful for studio genres like product, macro, and still life photography. Exact measurements of ambient light are needed to bring out all of the fine detail that can be lost if an image is even slightly over or underexposed.

Handheld incident light meters are used to directly measure the amount of light hitting a subject. This is done by placing the meter close to the subject; the white circular zone (lumisphere) is where lighting is collected for the measurement.

Light metering is the process of using either an in-camera system or handheld device to measure light and suggest the best settings. Aperture, shutter speed, and ISO are the three settings of the exposure triangle that can be adjusted for good exposure after the light metering process.

AmazonUVLight Sanitizer

Incident light metering is different from reflective metering because the device is measuring light before it reflects off of the subject. Therefore, you can get a slightly more accurate measurement of the total illumination in the area.

In order to understand how to use the light meter in-camera, we’ll need to discuss the three major ways your camera can meter. Each setting informs your camera as to what’s most important within the frame.

This is the most popular light metering because it can be used for nearly any scene or subject. Landscape photography and other genres that use the entire frame rely heavily on Matrix metering.

A light meter works by detecting the amount of light striking either the sensor or the subject. By following the information provided by the light meter, you can select the exposure triangle settings (aperture, shutter speed, ISO) that will result in optimal exposure for your subject.

Usually, you can view the light meter in camera along the base of the electronic viewfinder, optical viewfinder, or LCD screen. A simple line with sections and a -/+ axis makes up the entirety of the built-in exposure meter display.

A relatively new technology, excimer lamps emit a single wavelength. Lamps emitting wavelengths of 308nm (UVB), 222nm (UVC), and 207nm (UVC) have been developed. These ultraviolet light sources are not widely available yet, have the highest cost per bulb, and have an efficiency lower than low pressure mercury lamps.

Lastly, the importance of light metering and why good exposure leads to good pictures helps us close this chapter on understanding the light meter.

Ultraviolet lamp medical uses

UV-C germicidal bulbs and fixtures are most often used in medical settings to sanitize surfaces and clean rooms. Municipalities have long used UV-C for water purification. And with the increased awareness of the danger of airborne pathogens, the demand for UV-C for air purification has skyrocketed.

Light metering is also essential for film photography since improper exposure means poor grain, low tonality, and a potentially wasted frame. Look here for more information on film cameras and light meters!

The exposure meter is a gauge shown in the Electronic/Optical viewfinder or LCD screen that tells you how well-exposed your image will be. By referencing the exposure meter, you’ll know if you need to make adjustments to the light metering mode, available light, or exposure settings.

After this light metering tutorial, you’ll have a perfect understanding of what light metering in photography is and how to use metering for shooting great images!