In digital photography, the term color temperature sometimes refers to remapping of color values to simulate variations in ambient color temperature. Most digital cameras and raw image software provide presets simulating specific ambient values (e.g., sunny, cloudy, tungsten, etc.) while others allow explicit entry of white balance values in kelvins. These settings vary color values along the blue–yellow axis, while some software includes additional controls (sometimes labeled "tint") adding the magenta–green axis, and are to some extent arbitrary and a matter of artistic interpretation.[20]

The Sun may appear red, orange, yellow, or white from Earth, depending on its position in the sky. The changing color of the Sun over the course of the day is mainly a result of the scattering of sunlight and is not due to changes in black-body radiation. Rayleigh scattering of sunlight by Earth's atmosphere causes the blue color of the sky, which tends to scatter blue light more than red light.

Filters on a camera lens, or color gels over the light source(s) may be used to correct color balance. When shooting with a bluish light (high color temperature) source such as on an overcast day, in the shade, in window light, or if using tungsten film with white or blue light, a yellowish-orange filter will correct this. For shooting with daylight film (calibrated to 5600 K) under warmer (low color temperature) light sources such as sunsets, candlelight or tungsten lighting, a bluish (e.g. #80A) filter may be used. More-subtle filters are needed to correct for the difference between, say 3200 K and 3400 K tungsten lamps or to correct for the slightly blue cast of some flash tubes, which may be 6000 K.[21]

Some of the most common red wavelengths are 635 nm, 650 nm, and 670 nm. On the shorter end of the red spectral region, the wavelengths are more visible to the human eye, but they aren’t as easy to efficiently generate.

To the extent that a hot surface emits thermal radiation but is not an ideal black-body radiator, the color temperature of the light is not the actual temperature of the surface. An incandescent lamp's light is thermal radiation, and the bulb approximates an ideal black-body radiator, so its color temperature is essentially the temperature of the filament. Thus a relatively low temperature emits a dull red and a high temperature emits the almost white of the traditional incandescent light bulb. Metal workers are able to judge the temperature of hot metals by their color, from dark red to orange-white and then white (see red heat).

For most applications in astronomy (e.g., to place a star on the HR diagram or to determine the temperature of a model flux fitting an observed spectrum) the effective temperature is the quantity of interest. Various color-effective temperature relations exist in the literature. There relations also have smaller dependencies on other stellar parameters, such as the stellar metallicity and surface gravity[28]

CCT dimming for LED technology is regarded as a difficult task, since binning, age and temperature drift effects of LEDs change the actual color value output. Here feedback loop systems are used, for example with color sensors, to actively monitor and control the color output of multiple color mixing LEDs.[16]

Daylight has a spectrum similar to that of a black body with a correlated color temperature of 6500 K (D65 viewing standard) or 5500 K (daylight-balanced photographic film standard).

Photographic emulsion film does not respond to lighting color identically to the human retina or visual perception. An object that appears to the observer to be white may turn out to be very blue or orange in a photograph. The color balance may need to be corrected during printing to achieve a neutral color print. The extent of this correction is limited since color film normally has three layers sensitive to different colors and when used under the "wrong" light source, every layer may not respond proportionally, giving odd color casts in the shadows, although the mid-tones may have been correctly white-balanced under the enlarger. Light sources with discontinuous spectra, such as fluorescent tubes, cannot be fully corrected in printing either, since one of the layers may barely have recorded an image at all.

For lighting building interiors, it is often important to take into account the color temperature of illumination. A warmer (i.e., a lower color temperature) light is often used in public areas to promote relaxation, while a cooler (higher color temperature) light is used to enhance concentration, for example in schools and offices.[15]

Check out our Online Store: This page contains In-Stock products and an ever-changing assortment of various types of new lasers at marked-down/discount prices.

Light sources and illuminants may be characterized by their spectral power distribution (SPD). The relative SPD curves provided by many manufacturers may have been produced using 10 nm increments or more on their spectroradiometer.[26] The result is what would seem to be a smoother ("fuller spectrum") power distribution than the lamp actually has. Owing to their spiky distribution, much finer increments are advisable for taking measurements of fluorescent lights, and this requires more expensive equipment.

D50 is scientific shorthand for a standard illuminant: the daylight spectrum at a correlated color temperature of 5000 K. Similar definitions exist for D55, D65 and D75. Designations such as D50 are used to help classify color temperatures of light tables and viewing booths. When viewing a color slide at a light table, it is important that the light be balanced properly so that the colors are not shifted towards the red or blue.

In the desktop publishing industry, it is important to know a monitor's color temperature. Color matching software, such as Apple's ColorSync Utility for MacOS, measures a monitor's color temperature and then adjusts its settings accordingly. This enables on-screen color to more closely match printed color. Common monitor color temperatures, along with matching standard illuminants in parentheses, are as follows:

Red lasers typically emit light at around 650 nanometers. This wavelength corresponds to a specific range of energy levels in the laser medium, which can be achieved through various techniques such as gas discharge, solid-state, or diode pumping.

The color temperature of the electromagnetic radiation emitted from an ideal black body is defined as its surface temperature in kelvins, or alternatively in micro reciprocal degrees (mired).[11] This permits the definition of a standard by which light sources are compared.

The NTSC and PAL TV norms call for a compliant TV screen to display an electrically black and white signal (minimal color saturation) at a color temperature of 6500 K. On many consumer-grade televisions, there is a very noticeable deviation from this requirement. However, higher-end consumer-grade televisions can have their color temperatures adjusted to 6500 K by using a preprogrammed setting or a custom calibration. Current versions of ATSC explicitly call for the color temperature data to be included in the data stream, but old versions of ATSC allowed this data to be omitted. In this case, current versions of ATSC cite default colorimetry standards depending on the format. Both of the cited standards specify a 6500 K color temperature.

Color temperatures over 5000 K are called "cool colors" (bluish), while lower color temperatures (2700–3000 K) are called "warm colors" (yellowish). "Warm" in this context is with respect to a traditional categorization of colors, not a reference to black body temperature. The hue-heat hypothesis states that low color temperatures will feel warmer while higher color temperatures will feel cooler. The spectral peak of warm-colored light is closer to infrared, and most natural warm-colored light sources emit significant infrared radiation. The fact that "warm" lighting in this sense actually has a "cooler" color temperature often leads to confusion.[9]

Digital cameras, web graphics, DVDs, etc., are normally designed for a 6500 K color temperature. The sRGB standard commonly used for images on the Internet stipulates a 6500 K display white point.

The CIE color rendering index (CRI) is a method to determine how well a light source's illumination of eight sample patches compares to the illumination provided by a reference source. Cited together, the CRI and CCT give a numerical estimate of what reference (ideal) light source best approximates a particular artificial light, and what the difference is.

The Sun closely approximates a black-body radiator. The effective temperature, defined by the total radiative power per square unit, is 5772 K.[12] The color temperature of sunlight above the atmosphere is about 5900 K.[13]

As one of North America’s largest suppliers of red diode lasers, RPMC provides an extensive range of red laser solutions covering popular wavelengths like 635, 650, and 670 nm. Ideal for industrial, scientific, and commercial applications, our red lasers are available with options from single-mode to multimode, in free-space, fiber-coupled, and line generation configurations. With a variety of output powers and customizable packages, RPMC offers solutions that meet both precision and high-output demands. Our configurable platforms, from OEM to turnkey systems, ensure that you find the exact match for your application requirements. Whether for research or industrial use, RPMC delivers trusted performance and versatility.

Some daylight in the early morning and late afternoon (the golden hours) has a lower ("warmer") color temperature due to increased scattering of shorter-wavelength sunlight by atmospheric particulates – an optical phenomenon called the Tyndall effect.

If there is more than one light source with varied color temperatures, one way to balance the color is to use daylight film and place color-correcting gel filters over each light source.

Photographic film is made for specific light sources (most commonly daylight film and tungsten film), and, used properly, will create a neutral color print. Matching the sensitivity of the film to the color temperature of the light source is one way to balance color. If tungsten film is used indoors with incandescent lamps, the yellowish-orange light of the tungsten incandescent lamps will appear as white (3200 K) in the photograph. Color negative film is almost always daylight-balanced, since it is assumed that color can be adjusted in printing (with limitations, see above). Color transparency film, being the final artefact in the process, has to be matched to the light source or filters must be used to correct color.

Microsoft Windows prior to Windows 11 are use sRGB as default display color space, and use 6500 K as default display color temperature; this can be override by the GPU driver; ambient light sensors found on many new laptops can also adjust the display color temperature automatically. Windows 11 22H2 have supports for Auto Color Management (ACM) which further optimized for OLED monitors by reading EDID data.[22]

Lighting designers sometimes select filters by color temperature, commonly to match light that is theoretically white. Since fixtures using discharge type lamps produce a light of a considerably higher color temperature than do tungsten lamps, using the two in conjunction could potentially produce a stark contrast, so sometimes fixtures with HID lamps, commonly producing light of 6000–7000 K, are fitted with 3200 K filters to emulate tungsten light. Fixtures with color mixing features or with multiple colors (if including 3200 K), are also capable of producing tungsten-like light. Color temperature may also be a factor when selecting lamps, since each is likely to have a different color temperature.

Cinematographers do not "white balance" in the same way as video camera operators; they use techniques such as filters, choice of film stock, pre-flashing, and, after shooting, color grading, both by exposure at the labs and also digitally. Cinematographers also work closely with set designers and lighting crews to achieve the desired color effects.[23]

Many other light sources, such as fluorescent lamps, or light emitting diodes (LEDs) emit light primarily by processes other than thermal radiation. This means that the emitted radiation does not follow the form of a black-body spectrum. These sources are assigned what is known as a correlated color temperature (CCT). CCT is the color temperature of a black-body radiator which to human color perception most closely matches the light from the lamp. Because such an approximation is not required for incandescent light, the CCT for an incandescent light is simply its unadjusted temperature, derived from comparison to a black-body radiator.

Color temperature is a parameter describing the color of a visible light source by comparing it to the color of light emitted by an idealized opaque, non-reflective body. The temperature of the ideal emitter that matches the color most closely is defined as the color temperature of the original visible light source. The color temperature scale describes only the color of light emitted by a light source, which may actually be at a different (and often much lower) temperature.[1][2]

Red laser diodes, which are typically fabricated out of GaInP or AlGaInP, are the most popular and well-developed laser diodes available on the market today.  Red diode lasers are instrumental in a wide variety of applications ranging from inexpensive laser pointers to laboratory flow cytometry systems. 632.8 nm red light is the standard for helium-neon (HeNe) lasers, though they can produce green, yellow, and other wavelengths. HeNe lasers have been around for many years and are a tried-and-true staple in laboratories everywhere. Red HeNe lasers are often used for interferometry and laser alignment, for example. Wavelength-shifted DPSS lasers can produce red wavelengths through the process of harmonic generation (frequency doubling in this case). Red wavelengths can also be generated through the use of optical parametric oscillator (OPO) technology.

For artists, most pigments and papers have a cool or warm cast, as the human eye can detect even a minute amount of saturation. Gray mixed with yellow, orange, or red is a "warm gray". Green, blue, or purple create "cool grays". This sense of temperature is the reverse of that of real temperature; bluer is described as "cooler" even though it corresponds to a higher-temperature black body.

If you have any questions, or if you would like some assistance please contact us. Furthermore, you can email us at [email protected] to talk to a knowledgeable Product Manager.

In astronomy, the color temperature is defined by the local slope of the SPD at a given wavelength, or, in practice, a wavelength range. Given, for example, the color magnitudes B and V which are calibrated to be equal for an A0V star (e.g. Vega), the stellar color temperature T C {\displaystyle T_{C}} is given by the temperature for which the color index B − V {\displaystyle B-V} of a black-body radiator fits the stellar one. Besides the B − V {\displaystyle B-V} , other color indices can be used as well. The color temperature (as well as the correlated color temperature defined above) may differ largely from the effective temperature given by the radiative flux of the stellar surface. For example, the color temperature of an A0V star is about 15000 K compared to an effective temperature of about 9500 K.[27]

Photographers sometimes use color temperature meters. These are usually designed to read only two regions along the visible spectrum (red and blue); more expensive ones read three regions (red, green, and blue). However, they are ineffective with sources such as fluorescent or discharge lamps, whose light varies in color and may be harder to correct for. Because this light is often greenish, a magenta filter may correct it. More sophisticated colorimetry tools can be used if such meters are lacking.[21]

Color temperature has applications in lighting,[3] photography,[4] videography,[5] publishing,[6] manufacturing,[7] astrophysics,[8] and other fields. In practice, color temperature is most meaningful for light sources that correspond somewhat closely to the color of some black body, i.e., light in a range going from red to orange to yellow to white to bluish white. Although the concept of correlated color temperature extends the definition to any visible light, the color temperature of a green or a purple light rarely is useful information. Color temperature is conventionally expressed in kelvins, using the symbol K, a unit for absolute temperature.

Most video and digital still cameras can adjust for color temperature by zooming into a white or neutral colored object and setting the manual "white balance" (telling the camera that "this object is white"); the camera then shows true white as white and adjusts all the other colors accordingly. White-balancing is necessary especially when indoors under fluorescent lighting and when moving the camera from one lighting situation to another. Most cameras also have an automatic white balance function that attempts to determine the color of the light and correct accordingly. While these settings were once unreliable, they are much improved in today's digital cameras and produce an accurate white balance in a wide variety of lighting situations.

With 1000s of fielded units, and over 25 years of experience, providing OEMs, contract manufacturers, and researchers with the best laser solution for their application, our expert team is ready to help! Working with RPMC ensures you are getting trusted advice from our knowledgeable and technical staff on a wide range of laser products.  RPMC and our manufacturers are willing and able to provide custom solutions for your unique application.

For colors based on black-body theory, blue occurs at higher temperatures, whereas red occurs at lower temperatures. This is the opposite of the cultural associations attributed to colors, in which "red" is "hot", and "blue" is "cold".[14]

The output power can vary depending on the specific application, but they are generally low-power devices. Red lasers can be designed as continuous-wave or pulsed output and can be further modulated for specific use cases. They also often have a narrow spectral linewidth, which is useful for spectroscopy and other precision measurements.

However, in NTSC-J and NTSC-C standards, 9300 K color temperature is recommended. TVs and projectors sold in Japan, South Korea, China, Hong Kong, Taiwan and Philippines are usually adopt 9300 K as default settings. But for compatibility reasons, computer monitors sold in these country/region are usually adopt 6500 K as default settings; these color temperature settings are usually tuneable in OSD menu.

Video camera operators can white-balance objects that are not white, downplaying the color of the object used for white-balancing. For instance, they can bring more warmth into a picture by white-balancing off something that is light blue, such as faded blue denim; in this way white-balancing can replace a filter or lighting gel when those are not available.

For nearly 30 years, RPMC’s selection of Red Lasers has set the standard for affordable precision across a wide range of applications, from defense to medical, industrial, and research with 1000’s of successful units in the field. We understand that every application has unique requirements, which is why our configurable platforms are designed to offer the perfect fit for your needs—whether you’re working with fundamental wavelengths, harmonics, or specialty wavelengths. As your partner, we’re here to guide you through the selection process, ensuring that your red laser integrates seamlessly into your existing systems. With time-tested technology that balances power and precision, we’re committed to supporting your success every step of the way.