Bolt on the brightest off road LED Lighting solutions with kits designed specifically for your truck! Baja Designs, Vision X and KC Hi Lites deliver!

Next is to route the wire down under the truck. We recommend running the wire along the subframe. You can either zip tie the wire as you go or do so once you have it connected to the light bar.

HR carries bulbs in all sizes for OEM and aftermarket applications from Osram, Philips, XenonDepot, GTR Lighting, and Morimoto.

They have rubber vibration isolators to reduce the amount of shake the bar creates when on the road and in the wind. The vibration insulators are positioned in a way to give you total adjustability.

To adjust the light when connected to the mounting bracket, use an Allen key to turn the screw on either side of the bar. We recommend putting the whole setup on your truck and then adjusting it to where you think it will look good.

For our application, we used a GMC specification mounting bracket. We also got some spacers from the local hardware store to raise the bar’s height to shine over the top of the truck. First, we put the spacers on and then put the GMC bracket on the bottom of the bar.

Vision X has included some brackets in the kit to give you different mounting options that should cater to most applications.

Sometimes it's not all about utility. See and be Seen with our selection of high quality LED accessories for your truck!

Before putting the connector back onto the wire, we recommend starting from the battery before soldering. That way you will know how much wire you will need.

Modernize your classic car or truck, or Jeep with performance sealed beam headlights that use new LED projector optics for maximum output.

Though the light output is not as strong as back-lit alternatives, edge-lit Panels provide a smoother luminescence, resulting in more uniform light distribution. This is due to the PMMA light guide present in each edge-lit fitting; this material refracts lights from the horizontally mounted LEDs down into the room. The light guide plate must be made of the highest quality materials to prevent yellowing and ensure the continued performance of the fitting.

If possible, we recommend going somewhere dark and spread out and turning on your high beams and light bar. From there, adjust the light bar with either the Allen screw or mounting tabs.

Bolt-ons with all the bells and whistles built in! Morimoto's XB LED headlight assemblies are for truck owners who are unwilling to compromise.

If you are more of a visual learner, be sure to check out our video on how to install an LED light bar to your vehicle. While you are there, make sure to like and subscribe to our channel for the latest lighting upgrades for your vehicle.

We’ve got brighter headlights, badass light bars, and accent lighting for your Polaris, CAN-AM, and other off-road rigs! Rock on and Roll out!

Headlight Revolution specializes in lighting for trucks, but we invite you to contact us for a recommendation for any application!

Vision X pioneered the modern LED light bar as we know it. With their XPR LED Light Bar, they have created a benchmark for long-distance projection. Coming in at 29,133 Raw Lumens, the XPR will easily be able to light your way through the night.

Their 32-inch PRO6 LED Light Bar set is incredibly durable and produces more than enough light for your off-roading needs. If the light bar is not your speed, KC HiLites offers the bar in different sizes and the lights can be purchased individually.

For applications, edge-lit panels have virtually the same usage as back-lit (offices, corridors, school, and hospitals) but with more versatility. Since you don’t need to worry about panel depth being only 13mm thick, and our Kingston Range have an IP40 rated front face, they can be fittings in areas where low ceilings or dust is present.

LED Daytime Running Lights are growing in popularity, and our catalog is growing in size. We're delivering the best DRL upgrades from Morimoto.

LED bulbs add intensity and a modern look and feel to your car. Think about fitment, color, and the fine line between too much and not enough.

Grab your relay and regardless of where you mount it to, make sure it is facing upwards. If you have the wire end pointing up, you leave it prone to water retention that can short the connection.

LED Light Bars from benchmark brands like VisionX, Baja Designs, and Rigid Industries will help you turn the sun back on in the middle of the night.

High performance lights need high performance parts. HR has HID ballasts from the best brands, relay harnesses, PWM Modules, and other accessories.

With the most recent release of the Vision X XPR, you have the option for it to come with a smooth back-lit halo function that is SAE J3098 Compliant (up to 24in). The light bar can be purchased in several sizes ranging from 6-inches to 51-inches.

Keeping your wiring neat will make projects down the road easier and keep your engine bay looking clean. Be sure to route the wire slowly so you do not run it over any moving parts.

Just because we rely on our headlights to see, doesn't mean others aren't relying on our tail lights to see us. Tail Light Revolution!

In the realm of social media, Baja Designs has been making quite a buzz with their LP9 lights. So, we decided to take it upon ourselves to put these lights to the test. We ventured into the wilderness, the perfect setting to test the light outputs of these much-talked-about lights. The question on everyone's mind is, how do they perform in real-world conditions? We decided to pit them against one of the reigning champions in the field, the Diode Dynamics SS5, but we opted for the sport version.

To this day, HID for low beam headlights reigns king. It's ability to focus, create a proper beam pattern, and maximum output are unparalleled.

Get it installed properly with the right tools for the job. Headlight Revolution has everything you need to perform your upgrade like a pro.

We do not want to install the positive terminal just yet so we will put the negative wire on the outward-facing side of the battery. Remember, leave your positive wire alone for now.

Please note that not all states allow the use of light bars on the road, even in a backlit mode. Refer to your local laws for guidance and drive responsibly.

The XPR also features Prime Drive Technology from Vision X. This controls vital functions such as temperature and the diming of your LED Light Bar. PDT will allow for the LEDs to turn on and off in order to lower the bar’s overall temperature and maximize lifespan.

You do, however, need to cut the white plastic connector from the main wire. Before soldering anything, test the wires with a voltmeter to ensure you are not splicing wires that do not need to be spliced. In our case, we only used the red wire. The red wire is connected to our high beam wiring and the remaining XPR wires are taped shut with electrical tape.

Before we get into the installation, keep in mind that every light bar installation will be different. Everyone will have different vehicles which require different roll bars from various manufacturers. This is in addition to the fact that where you mount your bar, will change the amount of wiring you will need.

Every vehicle is different, but on ours, the roofline was a little high, so we utilized another set of spacers to mount our light bar bracket to the roll bar.

Eliminate Hyperflash or errors with the proper LED flasher relays or LED load resistors. Headlight Revolution has the parts you need to properly upgrade.

Rock lights are the best way to illuminate the wheel wells or under your vehicle. Function or for show, we've got today's best options to get it done.

Brighter and Whiter! A collection of vehicle specific LED Sidemarkers, truck mirrors, LED puddle lights, and LED license plate upgrades for your car & trucks!

Have any questions about one of the products we mentioned? Contact us today, and our customer service team would be happy to help.

From here you can run your switch for the bar into the cabin. We will get into the switch installation in a moment. But for our build, we opted to have the light bar connect to our high beams instead of routing into the cabin.

If you are interested in some more lighting for your vehicle, check out our rock light shootout video here to see some of the top rock light brands go against each other. We also took a closer look at the Rigid Industries, Vision X, and Profile Pixel LED Rock Lights in another blog post.

To route your wire to the light bar, begin by removing some plastic cladding inside the engine bay. A pry tool will be needed for the plastic clamps.

Rather than use the switch that came with the bar, we chose to use our high beams as the toggle for the light bar. Thankfully, Vision X’s switch can be unplugged from the button at the connector so there is no need to cut wires at this point.

It comes with two different mounting options. One being end-cap mounting and the other being Vision X’s patented mounting feet.

LumiRetro is a UK-based LED lighting supplier specialising in commercial and industrial solutions with advanced controls. They provide custom retrofit gear trays and offer a range of high-performance lighting products from brands like Balt LED, Zliss, NET LED Lighting, CP Electronics and Foxlux Emergency Lighting.

Be sure to tidy up your wiring with zip ties to avoid a messy appearance and from your wire snagging on any debris while off-roading.

Once you have mocked up where your wire will be routed, grab that connector your cut off at the beginning of our wiring job. Now you can solder that connection back together and plug it into the light bar.

Backup lights help you see. Brake lights help others see you. Both are overlooked safety features that deserve maximum output & contrast!

Unlike poor quality fluorescent battens and tubes, the Kingston and Ashley Panels don’t strobe, glare or flicker. Their flexible output provides students and teachers with the correct lighting levels needed in the classroom. This helps improve focus and prevent headaches and tiredness.

Back-lit Panels like our Ashley Range don’t have a light guide plate, reducing manufacturing costs and preventing discolouration of the diffuser. What’s more, because the LEDs point directly down, it provides a more light output and higher lumen per watt ratios than edge-lit alternatives. This means you need fewer fittings to light up a room, saving you money and time on installations!

Depending on where you have your XPR mounted, you may not have enough wire to reach your car’s battery. If your light is mounted on the hood, front bumper, or above the windscreen; you will most likely be able to reach the battery.

To hold the light bar and bracket together, we put the washers that came with the light bar and a 10mm nut under the bracket. Do not fully tighten these until you have your light in your ideal position.

After you have soldered your wires and zip-tied where needed, you can now connect that positive wire from before to the appropriate battery terminal.

Ideally, you want your beam to sit just above the high beam on your vehicle. In our test, we have the truck parked indoors so the position of the beam is not entirely accurate to how the real-life position will look.

Nobody puts more Plug n Play LED bulbs to the test than HR! Our selection of the best bulbs is always up to date with the newest options on the market!

Today we are looking at the retro-inspired KC HiLites that offer the best in performance and amenities. KC HiLites have been a staple of the off-road industry, both on and off the track since the 1970s. Their quality and performance are unmatched in that respect.

Once you have exposed the wires, twist and solder them together while using heat shrink, if you have some. Then, wrap the wires up with electrical tape.

To connect this wire, we routed it to the rock light connector and then spliced the white wire with our rock light’s power wire. This is so that when we turn on the rock lights, the backlight of the XPR would turn on as well.

It does not matter if you have a Jeep, a Ram, a GMC, or a Ford, if you like off-road lighting and light bars; this article is for you! We will be walking you through how to install the Vision X XPR light bar and all the tricky wiring so that you are ready for your next adventure.

With more than a decade of service in the industry, Headlight Revolution has helped thousands of individuals drastically improve their ability to see while driving in the dark. We represent more of the best truck lighting brands than any other distributor in the industry. We put the latest and greatest to the test to help you discover the truth in what works. We don't make the parts. We just know them well, mix in some great service, and make happy customers.

We have our XPR mounted on the rear roll bar, so we have to extend the wire. First, we cut the battery wire connector off the XPR’s cable system. Do not lose the connector.

With specific fitments for most every popular application, Morimoto's LED projector fog lights are the best way to bolt on performance for your fogs.

In terms of application, you’ll typically use back-lit panels in offices, corridors, schools, and hospitals. However, electricians must take the additional depth of the led panel into account in low ceiling applications, especially if the fitting has an emergency kit installed.

Remember, every installation is different. So, if you are unsure of how your wiring should go, consult an expert on the matter.

If you use the black brackets, they will be mounted to either end of the light bar. They can be mounted with two bolts and allow for your light bar to be adjusted up and down.