Take down lights were previously installed using bright halogen lights, but have become available for LED light bars, as well. These lights are primarily used by the police, and rarely available to use on emergency vehicles of other kinds, so make sure you check the laws and regulations for take down lights in your state.

Front operation light bars can turn on LED lights facing the front of the vehicle. If you buy cheap emergency visor lights, they only flash to the front.  Rear operation lights can turn on LED lights facing the back of vehicle. Full operation lights can turn on LED lights facing both the back and the front. Depending on the type, it may operate both sets at once exclusively, or may be able to independently operate either set at the front or back when needed.

For a standard LED module with a failure rate of 0.2% of LED modules per 1,000h, with 50 luminaires installed, the failure of two luminaires after only 20,000h must be expected, whereas ERCO High-Power LEDs provide an unchanged light impression.

Innovations inlighting

With a wide arrangement of 1:1.25 we recommend wallwashers with a 48 watt LED module to uniformly illuminate a facade with a height of 12m from a distance of 4m with approx. 50lx.

Put simply, take down lights are incredibly high intensity white lights that are to be fit to the front of the vehicle. You can even get take down lights on an interior led light bar. Their purpose is to produce a dazzling flash of light that is difficult for people to look at. Such such, it can offer the police an advantage in approaching or apprehending people in a dangerous situation, and prevent criminals from taking hostile action against the police since they are temporarily blinded.

As such, lights can change color depending on the circumstance. For instance, your police car light bar could use all blue lights when traveling on the road, then switch to flashing red and white when pulled over to a stop.

All ERCO outdoor luminaires have at least an IP65 protection rating. This means they are dustproof and protected against jets of water from all directions. Ground-recessed luminaires are also protected to IP68 against temporary immersion.

This dual color is achieved by having lights of multiple colors on one chip. These are usually some mix of primary colors, such as blue, green, and red. The controls can be programmed to turn on each color at a desired intensity. This means you can not only quickly switch between each primary color, but you can also mix them to produce a light of a new color.

Vertical illumination is simply and precisely implemented with pivotable Focalflood facade luminaires. Grazing light strikingly emphasises the surface structure and wide light distributions allow large spacings between the luminaires. Lighting design: Inwhite Ljusmiljö AB, Norrköping.

As mentioned, the ability for LED light bars to change their colors to suit their situation is impressive enough already. However, modern light bars can allow you to program your LEDs to display almost any color imaginable. This is done through the use of dual color output.

For general use in an area where maintaining visibility is easy enough, then Lo Power can ensure that you’re not blinding other drivers on the road, while also making maintaining a low energy consumption level. This can make sure you’re not draining your battery while you’re out using your LED light bar in normal circumstances.

However, when it comes to areas of low visibility, such as a winding country road or a busy street with plenty of vehicle lights to compete against, Hi Power can be precisely what you need. As the name indicates, this makes you lights significantly more powerful so that they can stand out and be more easily noticed.

Facade luminaires generate grazing light and highlight the surface structures of the materials On unstructured walls, gradients of light become the dominant characteristic and are seen as patterns independent of the building. Light patterns can be used to structure large, uniform surfaces. Beams of light that do not correspond to the architectural structure are perceived as distracting.

Extreme Tactical Dynamics offers a wide range of LED light bar options to meet all kinds of needs. However, when it comes to fitting emergency vehicle lights of any kind, you should be aware of the laws and regulations in your state dictating what you can and cannot use. We have a state-by-state resource looking over some of the laws, but we do not offer legal advice.

One of the most significant advantages of using light bars that use LED technology is that they can generate colored light much more easily than their halogen or strobe contemporaries. While other kinds of light bar use a white light paired with a colored lens to produce colored light effects, LED technology can generate lights of multiple colors right from the get go.

For vehicles that spend most of their time working on or close to roadways, traffic advisor functions can be added to LED light bars to ensure that other drivers notice and can safely maneuver around them.

Traffic advisor functions can include multiple flash functions using powerful LEDs that allow the operate to guide and control traffic in as safe a way as possible. This can include alerting others on the road to potential hazards, helping other drivers know when to navigate around a vehicle and which direction to take, and to keep the vehicle’s operator and any that they are assisting safe.

The right light for any type of facade: adjust the colour temperature dynamically or illuminate in colour. Luminaires with tunable white or RGBW allow scenographic lighting concepts.

Illumination of the widely projecting roofs with Kona projectors creates a memorable sight for visitors to Gyeongbokgung Palace in Seoul. Lighting design: bitzro & partners, Seoul.

Headlights are very limited in just how much they can pick up from the sides, which is what makes alley lights such a valuable and versatile addition to any emergency vehicle that is permitted to carry them.

You'll find the right size and lumen package for every lighting task. For projectors, floodlights and wallwashers the selection ranges from 2W/210lm to 96W/13200lm: ideal for both small and monumental facades.

Make sure you get the LED Light Bar that offers all of the functionality that you need, whether it an emergency light, or an off road light bar.

Another way to wallwash is by using grazing light. With this method, the details on facades are emphasised and highlighted by strong shadows. Grazing light is particularly effective on historical facades with interesting surfaces and reliefs. Facade luminaires and ground-recessed luminaires are ideal for this purpose.

ERCO luminaires for outdoor use require little maintenance and are particularly durable. The housing is made of corrosion-resistant cast aluminium, double powder coated. The no-rinse surface treatment ensures a reduced dirt deposit.

Floodlighting creates a very uniform distribution of light on the facade and makes it appear flat. Floodlights are suitable for mounting points opposite the facade, whereas wallwashers are the lighting tool of choice for mounting points on or in the ground.The wall distance (a) of lens wallwashers should be about one third of the facade height (h) for this purpose. This results in an angle of tilt (γ) of approx. 55°. Arrangement: a = 1/3 x h or γ = 55°For good linear uniformity the luminaire distance (d) of lens wallwashers can be up to 1.2 times the distance to the wall (a).Arrangement: d ≤ 1.2 x a

Impressive facade lighting makes buildings visible in the urban space and enables orientation. There are different methods of illuminating a building depending on the type, for example office building, historical building, residential building or museum. The uniform illumination of facades serves to emphasise landmarks and gives them a calm presence in the urban space. Light accents on the other hand structure large surfaces and highlight architectural details such as columns and cornices. Grazing light wallwashing is ideal with facades for highlighting the fine textures of timber and natural stone to create striking reliefs. To avoid light pollution, good glare control and precise lighting technology are important factors when selecting facade luminaires. Contour projectors, for example, illuminate the target surface with precisely defined rectangular beams of light. We give tips on how to strikingly illuminate facades in unison with the needs of both people and the environment. Lighting facades perfectly Download brochure

Furthermore, traffic advisor functions are built to be programmed in a variety of ways and to be updated or switched around as needed. After all, you may find your vehicle stopped in a variety of positions on the road which may require you to be able to deliver different instructions to other drivers on how they should navigate.

When you’re fitting emergency lights and the police light bar to a vehicle that you operate, you want to make sure that you invest in lights that meet your needs. You also want to ensure you’re getting lights with the functions that are going to help you. Here, we’re going to look into the different functions of an LED light bar, explaining what they do, as well as some of the situations in which the different options may be helpful.

High-output Lightscan projectors illuminate the facades of Milan Cathedral with high uniformity from close up and from large distances. Lighting design: Ferrara Palladino Lightscape, Pietro Palladino. Photography: Timm Lange.

Illumination lamp car

How you use your colored lights will be dictated by the regulations and laws in your state, however. Some colors are reserved for specific emergency services and vehicles, for instance, and the amber light bar is used generally as a tow truck light bar.

Ground-recessed luminaires emphasise landmarks with wide light distribution and uniform accentuation. Simple alignment of the light beam with use of pivotable luminaires avoids spill light at the Argentine Republic National Library. Architecture: Clorindo Testa, Francisco Bullrich, Alicia Cazzaniga. Lighting design: Estudio Juan Altgelt & Asociados. Photography: Alejandro Wirth.

Trinitylighting

You can use contour projectors to precisely adjust the size of the rectangular or square light cone. Two light distributions are available for both short and long lighting distances.

As with many of the functions of an LED Light Bar, use of traffic advisor functions may be limited in your state, so check your local laws and regulations to find out if you can fit them to your vehicle.

ERCO wants to offer you the best possible service. This website stores cookies for this purpose. By continuing to use this website, you consent to the use of cookies. For more information, please read our privacy policy. If you click on "Do not agree", essential cookies will continue to be set. Certain contents of external pages can no longer be displayed.

Make sure that you’re choosing the lights that you’re licensed and legally allowed to use. When you know what those are, Extreme Tactical Dynamics is here to offer the supply you need.

Different light colours enhance the nuanced nature of the facade. Warm light colours such as 3000K are suitable for warm-toned materials such as wood, whilst cooler light colours such as 4000K are more suitable for cooler surfaces such as exposed concrete. RGBW luminaires are ideal for scenographic lighting concepts on facades. Different levels of illuminance also enhance the differentiation of the facade. To render accents visible we recommend a brightness ratio to the general lighting of 1:5 to 1:10.

LED Light Bars are one of the most established and effective pieces of equipment to fit onto an emergency vehicle for the purposes of warning drivers of hazards on the road. For both indicating potential road hazards and indicating a need for drivers to make way, they allow emergency vehicles to respond to incidents as quickly and safely as possible.

Traffic advisor functions can come in a variety of sizes and with frames that can make them easy to install to any side of the vehicle. They have built-in dynamic controls that the vehicle operator can use inside or outside the vehicle as they demand.

Tesis Uplights achieve a striking long-distance effect for the vertical facade elements of the Brandsende office building, Hamburg. Architecture and lighting design: Akyol Kamps, Hamburg.

Many heritage buildings communicate their narrative via reliefs, ornamentation and sculptural elements. Nuanced illuminances, light distributions and light colours give the appearance of the facade a sense of rhythm. Harsh contrasts between accentuated and unilluminated zones can be balanced with floodlight general lighting.

ERCO luminaires for outdoors project light using highly efficient lens technology. This generates precisely defined beams of light of approximately 8° to 90° without spill light. Noteworthy is that high illuminance is achieved even at low wattages.

The direction in which your LED light bar can operate will change what kind of situations you can comfortably use it in. Some LED light bars can operate in only one direction, some can do it in both directions, and some can switch between them at will.

Illuminatinglight meaning

Transparent buildings with glass can be illuminated with light in different ways at night. If the view is to be directed into the building, a brightly lit interior helps and the building also seems to illuminate from the inside. This concept emphasises the spatial depth of the building. Alternatively, the supporting structure of the facade can be highlighted with light so that the structure of the glass plane becomes visible. Illuminating transparent glass is not recommended due to its reflection and transmission properties.

The emergency LED Light Bar is extremely versatile and can be used in a variety of ways to match the situation and the environment. If you need help finding the LED Light Bar with the functions that you need, don’t hesitate to get in touch with our team. With more than one type of led light bar for sale, we’ll be glad to help.

Grazing light strikingly emphasises the texture of the historic facade with its cornices. Site ground-recessed luminaires are highly discreet in the square of the Forney Library. Lighting design: Eclairage Conseil, Saint-Ouen-l'Aumône.

Dual color LEDs allow the lights to switch from one color to another in a moment. You don’t need to install extra lights and bulbs to switch colors, these lights can do it themselves.

Dual colors allow you to have an LED light bar that switches colors on the fly, but without having to take up more space by adding more chips or bulbs to your array.

The location of luminaire installation is one of the factors determining the lighting effect. ERCO offers various types of luminaire that illuminate facades from below, above, near or far. To illuminate facades from the ground, ground-recessed luminaires are a very elegant solution – the luminaires themselves remain almost invisible whilst only the effect of the lighting itself is noticed. Ground-recessed luminaires are available in six different light distributions. Facade luminaires on the other hand function as a discreet design element on the building and create a magical form of grazing light. Projectors, floodlights and wallwashers with up to seven light distributions allow mounting in almost any location: on the ground, on the facade, on bollards and on high masts. Matching accessories enable numerous mounting options.

Especially in outdoor applications, sustainable lighting solutions for ecologically exemplary applications are imperative to harmonise the needs of people, animals and plants at night. ERCO lighting tools make a significant contribution to this thanks to their high-precision optics and excellent glare control. They direct the light to exactly where you need it – without spill light. To completely avoid light pollution, we recommend that you make sure to correctly align the luminaires so that no light shines into the night sky. The right brightness also helps to protect the environment. This is why our luminaires for outdoor applications are dimmable.

Arkansaslighting

The material, form, texture and the light determine the appearance of facades. The impression of a facade changes over the course of the day due to the direction of light, the varying components of diffuse and direct light and the colour of the light. The correct combination of light distribution, light colour and light control creates striking facades in the evening. Various illuminances differentiate between areas of a facade. Grazing light highlights fine facade details. Floodlighting makes facades appear as a complete unit. Illumination outside of the facade plane should be prevented to avoid light pollution.

As the name suggests, alley lights are designed to help vehicle operators better see and explore areas hidden in darkness. This includes alleyways and other poorly light areas in nighttime conditions.

As such, the aim is to get LED Light Bars that offer a variety of flash patterns that incredibly conspicuous when turned on. As such, there should be two things in mind when looking at the flash patterns of different LED light bars:/p>

LED light bars are, naturally, designed to be highly visible to those on the road, even from a significant distance. The strobe light bar is designed to alert them to differences in traffic patterns, roadway obstructions, and other dangerous conditions.

Uplights give the facade a rhythmic structure. Ground-recessed luminaires mounted close to the facade generate grazing light and emphasise the surface structures of the materials. On unstructured walls, gradients of light become the dominant characteristic and are seen as patterns independent of the building. Light patterns can be used to structure large, uniform surfaces. Beams of light that do not correspond to the architectural structure are perceived as distracting.

Decisive factors for low-maintenance operation are maintenance of luminous flux and the failure rate of the LEDs. Comparing an ERCO high-performance LED (L90/B10) with a standard LED (L70/B50) demonstrates the positive effect of high-performance LEDs on investment costs. ERCO outdoor luminaires feature a failure rate of 0.1% of LEDs at up to 50,000h. This means that after just 20,000 operating hours, an approximately 10% higher luminous flux is generated with ERCO High-Power LEDs.

Tesis wallwashers installed in the floor impressively illuminate the wall painting at the Belmont Forum in Cloverdale. Precise light control and correct luminaire arrangements avoid light pollution. Lighting design: Lighting Options Australia, Perth. Photography: Matt Devlin, Perth.

As the name suggests, this feature allows you to adjust the power of your lights as necessary, increasing or decreasing the wattage depending on your needs at the time. Many LED strobe light bars have adjustable lights that you can operate with the flip of a switch or program to different strengths depending on your needs.

Your free myERCO account allows you to mark items, create product lists for your projects and request quotes. You also have continuous access to all ERCO media in the download area.

These are auxiliary lights that are usually added to the side of police cruisers and other emergency vehicles that allow the vehicle to light up areas to both the left and the right of the vehicle. As such, the operators can spot things that may otherwise be difficult to spot, such as a suspect fleeing down an alley or someone who is hurt in a poorly lit urban area.

Your state may have some regulations on just how powerful your lights can be, so check to make sure you’re operating within the limits of the law.

LF Illumination

Always the right light distribution – from accentuating small details to floodlighting high facades. With some luminaires, you can simply change the light distributions yourself.

In most cases, take down lights are simply bright halogen lights that are fitted to an LED light bar, rather than an LED light themselves.

The colors of the LED light bar can affect how well it meets these standards, but choosing one with a wide variety of flash patterns is the wisest course. As such, it can cycle through multiple patterns, alternative, splitting colors, progressively lighting different lights, and more, at different speeds. The more advanced the patterns are, the more likely it is to stand out enough to do the job.

As such, there are LEDs available in just about every color imaginable. Furthermore, color change LED technology can allow you to change the display as and when you need it. This opens up the possibilities to make your lights much more visible depending on the situation and the surroundings. Red lights may be more visible against the natural backdrop of a rural countryside, for instance, while blue lights may be more visible in urban settings.

Wallwashing illuminates facades in a uniform way and emphasises the dimension of the architecture as a whole. A major advantage in the design of urban spaces is that a vertical surface creates a high impression of brightness even with low illuminance. For efficient wallwashing with large spacing between luminaires, ERCO features specialised luminaires with wallwash light distribution in many of its product ranges.

ERCO offers luminaires for outdoor applications with up to ten different light distributions. The selection ranges from very narrow to wide light distributions. In this way a wide variety of lighting concepts can be implemented: from the precise accentuation of small details on a facade with narrow light distributions such as narrow spot (approx. 8°), spot (approx. 10° to 20°) and flood (approx. 30°) to the uniform floodlighting of large buildings with light distributions such as wide flood (approx. 50°), extra wide flood (approx. 90°) and wallwash (uniform wallwashing). Oval light distributions such as oval flood (approx. 20° x 60°) are also available and enable the highlighting of linear facade elements and logos. Contour projectors illuminate facade elements with a sharply defined beam of light. ERCO's high-quality optics enable you to achieve maximum illuminance on the target surface via precise LED technology.