Kenny's Burn Barrels Manufacturing and Engineering Co. P.O.Box 70476 Fairbanks, AK. 99707 (907) 456-BURN (2876) www.kennysburnbarrels.com Incinerators for burning paper, leaves, brush, wood, and debris. Product is made from 55-gallon drums and comes equipped with vents and screen tops. Electric Incinerators

If you allow bears to get into your garbage you risk prosecution under Alaska Department of Fish and Game regulation 5AAC 92.230. This regulation makes it illegal to negligently leave out food and garbage in a manner that attracts bears. The penalty is $100 per incident.

Rubbish incineratorprice

TASER™ M26C is field-proven with more than ten years in operation. It uses the same TASER™ cartridges as the TASER™ X26 and features a 5-second charge cycle that can be re-applied if necessary. This model is the preferred choice of many professionals, yet is now available for purchase by regular citizens. TASER™ Advanced M26c devices use proprietary technology to incapacitate dangerous subjects who pose a risk in a manner that is generally recognized as a safer alternative to other uses of force. TASER™ technology saves lives every day throughout the world. The TASER™ Advanced M26c utilizes compressed nitrogen to project two small probes 15 feet at a speed of 180 feet per second. These probes are connected to the TASER™ device by a high-voltage insulated wire. A 50,000 volt, a 26-watt electrical signal is transmitted throughout the region where the probes make contact with the body or clothing, resulting in an immediate loss of the person's neuromuscular control, balance and the ability to perform coordinated actions.

Mention in this document of commercial goods or services does not constitute an endorsement by the Alaska Department of Fish and Game.

Home garbageincinerator

Incinerators are generally two types: small, passive air flow incinerators that do not need electricity for fans or fuel pumps, and active flow incinerators that do require power. Passive flow incinerators, such as modified burn barrels (see example below), are more appropriate for recreational cabins or small camps where only one or two bags of garbage are produced a day. For camps producing larger amounts of garbage, active flow incinerators are more appropriate. Some models can be broken down to fit in small aircraft. You can incinerate anything with a food odor--food waste, cooking grease, cans, bottles, gray water residues, and most kitchen garbage. You should not incinerate anything that might explode or cause toxic fumes such s kitchen cleaning powders and sprays, treated lumber, batteries, or aerosol cans. In its "Policy on Human Food and Solid Waste Management and Bears in Alaska" the Alaska Department of Fish and Game states: "The preferred alternative for disposal of garbage that may attract bears is incineration at a facility that meets ADEC standards for combustible residue…Large field camps (more than 15 people) should dispose of garbage by daily incineration in a fuel-fired incinerator that meets ADEC standards…Small permanent facilities (e.g., lodges, weather stations) or large nonpermanent camps (e.g., project fires) should daily segregate and store garbage in a bear-proof container for backhaul to an approved disposal site. Alternatively, (a) putrescible waste and other combustibles could be incinerated in a locally fabricated incinerator meeting ADEC standards for residue." The pamphlet "Open Burning Policy & Guidelines" is available from the Alaska Department of Environmental Conservation, Division of Air Quality Air Permits Program. For Open Burning questions contact: Interior Alaska Kathy Stringham (907) 451-2114 Southcentral Alaska Cynthia Espinoza, (907) 269-7575 Southeast Alaska & Aleutians Jeanette Brena (907) 465-5122 Safety Information Used improperly or in extreme conditions burn barrels and incinerators can cause wildfires! Complete incineration of wet garbage items requires a slow burning fuel, such as diesel or kerosene, or the aid of propane or electricity. Regardless of what you use all incinerators require plenty of air to work properly. Only non-toxic materials should be burned in incinerators. Incinerators in areas accessible to bears should be cleaned at regular intervals, as residues can an attractant. Accumulation of ash can also blocking air flow. Incineration of garbage can leave a temporary odor trail that a bear could follow. Where feasible, the incinerator should be located downwind from the camp or tent area (and inside the electric fence if there is one). Burning should be scheduled during the day or immediately after dinner when people are still awake and active. Directions for building your own incinerator "Yukon Incinerator" A camp producing one full garbage bag a day can use a homebuilt incinerator made from fuel drums. Larger camps can get by with similar homebuilt models, made from culverts, but should look to efficient forced-air, fuel-fired, or electric commercial incinerators. See below for vendors. Before you get started building your own incinerator, you should consider the design carefully: Garbage must get really hot before it will incinerate. The sizes of the vent and chimney are critical to get the airflow required to support a hot fire. If it doesn't burn well, raise the chimney. "Empty" fuel drums need to be steamed or washed out, or filled with water or exhaust before they are cut or welded. If not, residual fuel fumes can cause serious explosions Avoid using gas drums. Most garbage is too wet to burn on its own. To prevent explosions, slow burning fuels like diesel or stove oil, wood or cardboard should be used rather than highly flammable fuels. A lighter torch may be used in the vent to start the fire. Suspending the garbage in a steel mesh basket or by a grill helps dry it out and ensure that the airflow is maintained. A removable basket greatly simplifies ash removal. Size the burn chamber for one bag of garbage. Don't store garbage in your incinerator "until there is enough for a good burn." If you leave wet garbage in the incinerator it will attract bears. IMPORTANT: The Alaska Department of Fish and Game does not guarantee nor warrant the design, effectiveness and/or safety of these devices under any circumstances. Train every incinerator operator in the safe use of the incinerators. Suggestions for building your own incinerator are contained in the attached files. Vendors Small Incinerators Aleckson Fabricators 38735 S. Ruby Circle Soldotna, Alaska 907-262-9654 shirley@alaska.net This incinerator weighs approximately 150 pounds and comes apart into two sections for easy transportation by 4 wheeler, snowmachine, boat, or appropriate aircraft. A demonstration model of this incinerator can be seen at the ADF&G office in Soldotna or in Spring 2004 in the Caribou Hills on the Kenai Peninsula. Aleckson Fabricators also makes bear-resistant containers from aluminum and steel. Kenny's Burn Barrels Manufacturing and Engineering Co. P.O.Box 70476 Fairbanks, AK. 99707 (907) 456-BURN (2876) www.kennysburnbarrels.com Incinerators for burning paper, leaves, brush, wood, and debris. Product is made from 55-gallon drums and comes equipped with vents and screen tops. Electric Incinerators Spill Shield Environmental 2000 W. International Airport Road #D2 Anchorage, Alaska 99502 907-561-6033 www.spillshield.com Electrically powered 110-volt incinerator. Innovative combustion system meets EPA air quality emission standards for burning non-hazardous waste. Uses a standard 55-gallon drum. Used in Alaska by DEC, US National Park Service, and the US Army. Forced Air-Diesel Fueled Incinerators Taiga Ventures 2700 S. Cushman Street Fairbanks, Alaska 99701 907-452-6631 www.taigaventures.com Compact, high efficiency, forced air, diesel fueled incinerators manufactured and sized for customer needs. Facebook Twitter Google+ Reddit

From experience items no working or appear to be defective could be an oversight on how to use and operate. Call us soon as possible so we can assist you determining if the item is defective or operational issue. If defective, we will issue return authorization number, and coordinate a replacement soon as possible.

Soon as possible, call our support line (888) 747-20111 to report any packages received damaged while in transit to you. We will file claims with the carrier on your behalf. It is important to save the package, images if possible and share with us within 5 days.

Smallrubbish incinerator

Taiga Ventures 2700 S. Cushman Street Fairbanks, Alaska 99701 907-452-6631 www.taigaventures.com Compact, high efficiency, forced air, diesel fueled incinerators manufactured and sized for customer needs.

Garbage incinerators can save time and money. They can be located close to camp and the limited ash does not require heavy hauling. Bear damage to your camp, cabin, or lodge can cost thousands of dollars to repair. Open pit fires can cause costly tent and forest fires. Garbage hauls to town dumps can be costly in the long run.

Rubbish incineratorfor home

For any items that are serviceable, if the service was unauthorized and not approved by Self Defense Products Inc, the warranty will no longer be valid and void.

Complete incineration of wet garbage items requires a slow burning fuel, such as diesel or kerosene, or the aid of propane or electricity. Regardless of what you use all incinerators require plenty of air to work properly. Only non-toxic materials should be burned in incinerators. Incinerators in areas accessible to bears should be cleaned at regular intervals, as residues can an attractant. Accumulation of ash can also blocking air flow. Incineration of garbage can leave a temporary odor trail that a bear could follow. Where feasible, the incinerator should be located downwind from the camp or tent area (and inside the electric fence if there is one). Burning should be scheduled during the day or immediately after dinner when people are still awake and active. Directions for building your own incinerator "Yukon Incinerator" A camp producing one full garbage bag a day can use a homebuilt incinerator made from fuel drums. Larger camps can get by with similar homebuilt models, made from culverts, but should look to efficient forced-air, fuel-fired, or electric commercial incinerators. See below for vendors. Before you get started building your own incinerator, you should consider the design carefully: Garbage must get really hot before it will incinerate. The sizes of the vent and chimney are critical to get the airflow required to support a hot fire. If it doesn't burn well, raise the chimney. "Empty" fuel drums need to be steamed or washed out, or filled with water or exhaust before they are cut or welded. If not, residual fuel fumes can cause serious explosions Avoid using gas drums. Most garbage is too wet to burn on its own. To prevent explosions, slow burning fuels like diesel or stove oil, wood or cardboard should be used rather than highly flammable fuels. A lighter torch may be used in the vent to start the fire. Suspending the garbage in a steel mesh basket or by a grill helps dry it out and ensure that the airflow is maintained. A removable basket greatly simplifies ash removal. Size the burn chamber for one bag of garbage. Don't store garbage in your incinerator "until there is enough for a good burn." If you leave wet garbage in the incinerator it will attract bears. IMPORTANT: The Alaska Department of Fish and Game does not guarantee nor warrant the design, effectiveness and/or safety of these devices under any circumstances. Train every incinerator operator in the safe use of the incinerators. Suggestions for building your own incinerator are contained in the attached files. Vendors Small Incinerators Aleckson Fabricators 38735 S. Ruby Circle Soldotna, Alaska 907-262-9654 shirley@alaska.net This incinerator weighs approximately 150 pounds and comes apart into two sections for easy transportation by 4 wheeler, snowmachine, boat, or appropriate aircraft. A demonstration model of this incinerator can be seen at the ADF&G office in Soldotna or in Spring 2004 in the Caribou Hills on the Kenai Peninsula. Aleckson Fabricators also makes bear-resistant containers from aluminum and steel. Kenny's Burn Barrels Manufacturing and Engineering Co. P.O.Box 70476 Fairbanks, AK. 99707 (907) 456-BURN (2876) www.kennysburnbarrels.com Incinerators for burning paper, leaves, brush, wood, and debris. Product is made from 55-gallon drums and comes equipped with vents and screen tops. Electric Incinerators Spill Shield Environmental 2000 W. International Airport Road #D2 Anchorage, Alaska 99502 907-561-6033 www.spillshield.com Electrically powered 110-volt incinerator. Innovative combustion system meets EPA air quality emission standards for burning non-hazardous waste. Uses a standard 55-gallon drum. Used in Alaska by DEC, US National Park Service, and the US Army. Forced Air-Diesel Fueled Incinerators Taiga Ventures 2700 S. Cushman Street Fairbanks, Alaska 99701 907-452-6631 www.taigaventures.com Compact, high efficiency, forced air, diesel fueled incinerators manufactured and sized for customer needs. Facebook Twitter Google+ Reddit

Commercial garbageincinerator

Our primary goal is a satisfied customer meeting all your personal and home security needs. We offer one of the best money back guarantees for the self defense home security products industry!

If you are less than satisfied with any of our products within 30 days from the receipt of your items, please call us toll free at (888) 747-2011 to secure a Return Authorization (RA) number.

Spill Shield Environmental 2000 W. International Airport Road #D2 Anchorage, Alaska 99502 907-561-6033 www.spillshield.com Electrically powered 110-volt incinerator. Innovative combustion system meets EPA air quality emission standards for burning non-hazardous waste. Uses a standard 55-gallon drum. Used in Alaska by DEC, US National Park Service, and the US Army. Forced Air-Diesel Fueled Incinerators

Before you get started building your own incinerator, you should consider the design carefully: Garbage must get really hot before it will incinerate. The sizes of the vent and chimney are critical to get the airflow required to support a hot fire. If it doesn't burn well, raise the chimney. "Empty" fuel drums need to be steamed or washed out, or filled with water or exhaust before they are cut or welded. If not, residual fuel fumes can cause serious explosions Avoid using gas drums. Most garbage is too wet to burn on its own. To prevent explosions, slow burning fuels like diesel or stove oil, wood or cardboard should be used rather than highly flammable fuels. A lighter torch may be used in the vent to start the fire. Suspending the garbage in a steel mesh basket or by a grill helps dry it out and ensure that the airflow is maintained. A removable basket greatly simplifies ash removal. Size the burn chamber for one bag of garbage. Don't store garbage in your incinerator "until there is enough for a good burn." If you leave wet garbage in the incinerator it will attract bears. IMPORTANT: The Alaska Department of Fish and Game does not guarantee nor warrant the design, effectiveness and/or safety of these devices under any circumstances. Train every incinerator operator in the safe use of the incinerators. Suggestions for building your own incinerator are contained in the attached files. Vendors Small Incinerators Aleckson Fabricators 38735 S. Ruby Circle Soldotna, Alaska 907-262-9654 shirley@alaska.net This incinerator weighs approximately 150 pounds and comes apart into two sections for easy transportation by 4 wheeler, snowmachine, boat, or appropriate aircraft. A demonstration model of this incinerator can be seen at the ADF&G office in Soldotna or in Spring 2004 in the Caribou Hills on the Kenai Peninsula. Aleckson Fabricators also makes bear-resistant containers from aluminum and steel. Kenny's Burn Barrels Manufacturing and Engineering Co. P.O.Box 70476 Fairbanks, AK. 99707 (907) 456-BURN (2876) www.kennysburnbarrels.com Incinerators for burning paper, leaves, brush, wood, and debris. Product is made from 55-gallon drums and comes equipped with vents and screen tops. Electric Incinerators Spill Shield Environmental 2000 W. International Airport Road #D2 Anchorage, Alaska 99502 907-561-6033 www.spillshield.com Electrically powered 110-volt incinerator. Innovative combustion system meets EPA air quality emission standards for burning non-hazardous waste. Uses a standard 55-gallon drum. Used in Alaska by DEC, US National Park Service, and the US Army. Forced Air-Diesel Fueled Incinerators Taiga Ventures 2700 S. Cushman Street Fairbanks, Alaska 99701 907-452-6631 www.taigaventures.com Compact, high efficiency, forced air, diesel fueled incinerators manufactured and sized for customer needs. Facebook Twitter Google+ Reddit

In its "Policy on Human Food and Solid Waste Management and Bears in Alaska" the Alaska Department of Fish and Game states: "The preferred alternative for disposal of garbage that may attract bears is incineration at a facility that meets ADEC standards for combustible residue…Large field camps (more than 15 people) should dispose of garbage by daily incineration in a fuel-fired incinerator that meets ADEC standards…Small permanent facilities (e.g., lodges, weather stations) or large nonpermanent camps (e.g., project fires) should daily segregate and store garbage in a bear-proof container for backhaul to an approved disposal site. Alternatively, (a) putrescible waste and other combustibles could be incinerated in a locally fabricated incinerator meeting ADEC standards for residue." The pamphlet "Open Burning Policy & Guidelines" is available from the Alaska Department of Environmental Conservation, Division of Air Quality Air Permits Program. For Open Burning questions contact: Interior Alaska Kathy Stringham (907) 451-2114 Southcentral Alaska Cynthia Espinoza, (907) 269-7575 Southeast Alaska & Aleutians Jeanette Brena (907) 465-5122 Safety Information Used improperly or in extreme conditions burn barrels and incinerators can cause wildfires! Complete incineration of wet garbage items requires a slow burning fuel, such as diesel or kerosene, or the aid of propane or electricity. Regardless of what you use all incinerators require plenty of air to work properly. Only non-toxic materials should be burned in incinerators. Incinerators in areas accessible to bears should be cleaned at regular intervals, as residues can an attractant. Accumulation of ash can also blocking air flow. Incineration of garbage can leave a temporary odor trail that a bear could follow. Where feasible, the incinerator should be located downwind from the camp or tent area (and inside the electric fence if there is one). Burning should be scheduled during the day or immediately after dinner when people are still awake and active. Directions for building your own incinerator "Yukon Incinerator" A camp producing one full garbage bag a day can use a homebuilt incinerator made from fuel drums. Larger camps can get by with similar homebuilt models, made from culverts, but should look to efficient forced-air, fuel-fired, or electric commercial incinerators. See below for vendors. Before you get started building your own incinerator, you should consider the design carefully: Garbage must get really hot before it will incinerate. The sizes of the vent and chimney are critical to get the airflow required to support a hot fire. If it doesn't burn well, raise the chimney. "Empty" fuel drums need to be steamed or washed out, or filled with water or exhaust before they are cut or welded. If not, residual fuel fumes can cause serious explosions Avoid using gas drums. Most garbage is too wet to burn on its own. To prevent explosions, slow burning fuels like diesel or stove oil, wood or cardboard should be used rather than highly flammable fuels. A lighter torch may be used in the vent to start the fire. Suspending the garbage in a steel mesh basket or by a grill helps dry it out and ensure that the airflow is maintained. A removable basket greatly simplifies ash removal. Size the burn chamber for one bag of garbage. Don't store garbage in your incinerator "until there is enough for a good burn." If you leave wet garbage in the incinerator it will attract bears. IMPORTANT: The Alaska Department of Fish and Game does not guarantee nor warrant the design, effectiveness and/or safety of these devices under any circumstances. Train every incinerator operator in the safe use of the incinerators. Suggestions for building your own incinerator are contained in the attached files. Vendors Small Incinerators Aleckson Fabricators 38735 S. Ruby Circle Soldotna, Alaska 907-262-9654 shirley@alaska.net This incinerator weighs approximately 150 pounds and comes apart into two sections for easy transportation by 4 wheeler, snowmachine, boat, or appropriate aircraft. A demonstration model of this incinerator can be seen at the ADF&G office in Soldotna or in Spring 2004 in the Caribou Hills on the Kenai Peninsula. Aleckson Fabricators also makes bear-resistant containers from aluminum and steel. Kenny's Burn Barrels Manufacturing and Engineering Co. P.O.Box 70476 Fairbanks, AK. 99707 (907) 456-BURN (2876) www.kennysburnbarrels.com Incinerators for burning paper, leaves, brush, wood, and debris. Product is made from 55-gallon drums and comes equipped with vents and screen tops. Electric Incinerators Spill Shield Environmental 2000 W. International Airport Road #D2 Anchorage, Alaska 99502 907-561-6033 www.spillshield.com Electrically powered 110-volt incinerator. Innovative combustion system meets EPA air quality emission standards for burning non-hazardous waste. Uses a standard 55-gallon drum. Used in Alaska by DEC, US National Park Service, and the US Army. Forced Air-Diesel Fueled Incinerators Taiga Ventures 2700 S. Cushman Street Fairbanks, Alaska 99701 907-452-6631 www.taigaventures.com Compact, high efficiency, forced air, diesel fueled incinerators manufactured and sized for customer needs. Facebook Twitter Google+ Reddit

Rubbish incineratorfor sale

"The preferred alternative for disposal of garbage that may attract bears is incineration at a facility that meets ADEC standards for combustible residue…Large field camps (more than 15 people) should dispose of garbage by daily incineration in a fuel-fired incinerator that meets ADEC standards…Small permanent facilities (e.g., lodges, weather stations) or large nonpermanent camps (e.g., project fires) should daily segregate and store garbage in a bear-proof container for backhaul to an approved disposal site. Alternatively, (a) putrescible waste and other combustibles could be incinerated in a locally fabricated incinerator meeting ADEC standards for residue." The pamphlet "Open Burning Policy & Guidelines" is available from the Alaska Department of Environmental Conservation, Division of Air Quality Air Permits Program. For Open Burning questions contact: Interior Alaska Kathy Stringham (907) 451-2114 Southcentral Alaska Cynthia Espinoza, (907) 269-7575 Southeast Alaska & Aleutians Jeanette Brena (907) 465-5122 Safety Information Used improperly or in extreme conditions burn barrels and incinerators can cause wildfires! Complete incineration of wet garbage items requires a slow burning fuel, such as diesel or kerosene, or the aid of propane or electricity. Regardless of what you use all incinerators require plenty of air to work properly. Only non-toxic materials should be burned in incinerators. Incinerators in areas accessible to bears should be cleaned at regular intervals, as residues can an attractant. Accumulation of ash can also blocking air flow. Incineration of garbage can leave a temporary odor trail that a bear could follow. Where feasible, the incinerator should be located downwind from the camp or tent area (and inside the electric fence if there is one). Burning should be scheduled during the day or immediately after dinner when people are still awake and active. Directions for building your own incinerator "Yukon Incinerator" A camp producing one full garbage bag a day can use a homebuilt incinerator made from fuel drums. Larger camps can get by with similar homebuilt models, made from culverts, but should look to efficient forced-air, fuel-fired, or electric commercial incinerators. See below for vendors. Before you get started building your own incinerator, you should consider the design carefully: Garbage must get really hot before it will incinerate. The sizes of the vent and chimney are critical to get the airflow required to support a hot fire. If it doesn't burn well, raise the chimney. "Empty" fuel drums need to be steamed or washed out, or filled with water or exhaust before they are cut or welded. If not, residual fuel fumes can cause serious explosions Avoid using gas drums. Most garbage is too wet to burn on its own. To prevent explosions, slow burning fuels like diesel or stove oil, wood or cardboard should be used rather than highly flammable fuels. A lighter torch may be used in the vent to start the fire. Suspending the garbage in a steel mesh basket or by a grill helps dry it out and ensure that the airflow is maintained. A removable basket greatly simplifies ash removal. Size the burn chamber for one bag of garbage. Don't store garbage in your incinerator "until there is enough for a good burn." If you leave wet garbage in the incinerator it will attract bears. IMPORTANT: The Alaska Department of Fish and Game does not guarantee nor warrant the design, effectiveness and/or safety of these devices under any circumstances. Train every incinerator operator in the safe use of the incinerators. Suggestions for building your own incinerator are contained in the attached files. Vendors Small Incinerators Aleckson Fabricators 38735 S. Ruby Circle Soldotna, Alaska 907-262-9654 shirley@alaska.net This incinerator weighs approximately 150 pounds and comes apart into two sections for easy transportation by 4 wheeler, snowmachine, boat, or appropriate aircraft. A demonstration model of this incinerator can be seen at the ADF&G office in Soldotna or in Spring 2004 in the Caribou Hills on the Kenai Peninsula. Aleckson Fabricators also makes bear-resistant containers from aluminum and steel. Kenny's Burn Barrels Manufacturing and Engineering Co. P.O.Box 70476 Fairbanks, AK. 99707 (907) 456-BURN (2876) www.kennysburnbarrels.com Incinerators for burning paper, leaves, brush, wood, and debris. Product is made from 55-gallon drums and comes equipped with vents and screen tops. Electric Incinerators Spill Shield Environmental 2000 W. International Airport Road #D2 Anchorage, Alaska 99502 907-561-6033 www.spillshield.com Electrically powered 110-volt incinerator. Innovative combustion system meets EPA air quality emission standards for burning non-hazardous waste. Uses a standard 55-gallon drum. Used in Alaska by DEC, US National Park Service, and the US Army. Forced Air-Diesel Fueled Incinerators Taiga Ventures 2700 S. Cushman Street Fairbanks, Alaska 99701 907-452-6631 www.taigaventures.com Compact, high efficiency, forced air, diesel fueled incinerators manufactured and sized for customer needs. Facebook Twitter Google+ Reddit

Incineration of garbage can leave a temporary odor trail that a bear could follow. Where feasible, the incinerator should be located downwind from the camp or tent area (and inside the electric fence if there is one). Burning should be scheduled during the day or immediately after dinner when people are still awake and active. Directions for building your own incinerator "Yukon Incinerator" A camp producing one full garbage bag a day can use a homebuilt incinerator made from fuel drums. Larger camps can get by with similar homebuilt models, made from culverts, but should look to efficient forced-air, fuel-fired, or electric commercial incinerators. See below for vendors. Before you get started building your own incinerator, you should consider the design carefully: Garbage must get really hot before it will incinerate. The sizes of the vent and chimney are critical to get the airflow required to support a hot fire. If it doesn't burn well, raise the chimney. "Empty" fuel drums need to be steamed or washed out, or filled with water or exhaust before they are cut or welded. If not, residual fuel fumes can cause serious explosions Avoid using gas drums. Most garbage is too wet to burn on its own. To prevent explosions, slow burning fuels like diesel or stove oil, wood or cardboard should be used rather than highly flammable fuels. A lighter torch may be used in the vent to start the fire. Suspending the garbage in a steel mesh basket or by a grill helps dry it out and ensure that the airflow is maintained. A removable basket greatly simplifies ash removal. Size the burn chamber for one bag of garbage. Don't store garbage in your incinerator "until there is enough for a good burn." If you leave wet garbage in the incinerator it will attract bears. IMPORTANT: The Alaska Department of Fish and Game does not guarantee nor warrant the design, effectiveness and/or safety of these devices under any circumstances. Train every incinerator operator in the safe use of the incinerators. Suggestions for building your own incinerator are contained in the attached files. Vendors Small Incinerators Aleckson Fabricators 38735 S. Ruby Circle Soldotna, Alaska 907-262-9654 shirley@alaska.net This incinerator weighs approximately 150 pounds and comes apart into two sections for easy transportation by 4 wheeler, snowmachine, boat, or appropriate aircraft. A demonstration model of this incinerator can be seen at the ADF&G office in Soldotna or in Spring 2004 in the Caribou Hills on the Kenai Peninsula. Aleckson Fabricators also makes bear-resistant containers from aluminum and steel. Kenny's Burn Barrels Manufacturing and Engineering Co. P.O.Box 70476 Fairbanks, AK. 99707 (907) 456-BURN (2876) www.kennysburnbarrels.com Incinerators for burning paper, leaves, brush, wood, and debris. Product is made from 55-gallon drums and comes equipped with vents and screen tops. Electric Incinerators Spill Shield Environmental 2000 W. International Airport Road #D2 Anchorage, Alaska 99502 907-561-6033 www.spillshield.com Electrically powered 110-volt incinerator. Innovative combustion system meets EPA air quality emission standards for burning non-hazardous waste. Uses a standard 55-gallon drum. Used in Alaska by DEC, US National Park Service, and the US Army. Forced Air-Diesel Fueled Incinerators Taiga Ventures 2700 S. Cushman Street Fairbanks, Alaska 99701 907-452-6631 www.taigaventures.com Compact, high efficiency, forced air, diesel fueled incinerators manufactured and sized for customer needs. Facebook Twitter Google+ Reddit

You can incinerate anything with a food odor--food waste, cooking grease, cans, bottles, gray water residues, and most kitchen garbage. You should not incinerate anything that might explode or cause toxic fumes such s kitchen cleaning powders and sprays, treated lumber, batteries, or aerosol cans. In its "Policy on Human Food and Solid Waste Management and Bears in Alaska" the Alaska Department of Fish and Game states: "The preferred alternative for disposal of garbage that may attract bears is incineration at a facility that meets ADEC standards for combustible residue…Large field camps (more than 15 people) should dispose of garbage by daily incineration in a fuel-fired incinerator that meets ADEC standards…Small permanent facilities (e.g., lodges, weather stations) or large nonpermanent camps (e.g., project fires) should daily segregate and store garbage in a bear-proof container for backhaul to an approved disposal site. Alternatively, (a) putrescible waste and other combustibles could be incinerated in a locally fabricated incinerator meeting ADEC standards for residue." The pamphlet "Open Burning Policy & Guidelines" is available from the Alaska Department of Environmental Conservation, Division of Air Quality Air Permits Program. For Open Burning questions contact: Interior Alaska Kathy Stringham (907) 451-2114 Southcentral Alaska Cynthia Espinoza, (907) 269-7575 Southeast Alaska & Aleutians Jeanette Brena (907) 465-5122 Safety Information Used improperly or in extreme conditions burn barrels and incinerators can cause wildfires! Complete incineration of wet garbage items requires a slow burning fuel, such as diesel or kerosene, or the aid of propane or electricity. Regardless of what you use all incinerators require plenty of air to work properly. Only non-toxic materials should be burned in incinerators. Incinerators in areas accessible to bears should be cleaned at regular intervals, as residues can an attractant. Accumulation of ash can also blocking air flow. Incineration of garbage can leave a temporary odor trail that a bear could follow. Where feasible, the incinerator should be located downwind from the camp or tent area (and inside the electric fence if there is one). Burning should be scheduled during the day or immediately after dinner when people are still awake and active. Directions for building your own incinerator "Yukon Incinerator" A camp producing one full garbage bag a day can use a homebuilt incinerator made from fuel drums. Larger camps can get by with similar homebuilt models, made from culverts, but should look to efficient forced-air, fuel-fired, or electric commercial incinerators. See below for vendors. Before you get started building your own incinerator, you should consider the design carefully: Garbage must get really hot before it will incinerate. The sizes of the vent and chimney are critical to get the airflow required to support a hot fire. If it doesn't burn well, raise the chimney. "Empty" fuel drums need to be steamed or washed out, or filled with water or exhaust before they are cut or welded. If not, residual fuel fumes can cause serious explosions Avoid using gas drums. Most garbage is too wet to burn on its own. To prevent explosions, slow burning fuels like diesel or stove oil, wood or cardboard should be used rather than highly flammable fuels. A lighter torch may be used in the vent to start the fire. Suspending the garbage in a steel mesh basket or by a grill helps dry it out and ensure that the airflow is maintained. A removable basket greatly simplifies ash removal. Size the burn chamber for one bag of garbage. Don't store garbage in your incinerator "until there is enough for a good burn." If you leave wet garbage in the incinerator it will attract bears. IMPORTANT: The Alaska Department of Fish and Game does not guarantee nor warrant the design, effectiveness and/or safety of these devices under any circumstances. Train every incinerator operator in the safe use of the incinerators. Suggestions for building your own incinerator are contained in the attached files. Vendors Small Incinerators Aleckson Fabricators 38735 S. Ruby Circle Soldotna, Alaska 907-262-9654 shirley@alaska.net This incinerator weighs approximately 150 pounds and comes apart into two sections for easy transportation by 4 wheeler, snowmachine, boat, or appropriate aircraft. A demonstration model of this incinerator can be seen at the ADF&G office in Soldotna or in Spring 2004 in the Caribou Hills on the Kenai Peninsula. Aleckson Fabricators also makes bear-resistant containers from aluminum and steel. Kenny's Burn Barrels Manufacturing and Engineering Co. P.O.Box 70476 Fairbanks, AK. 99707 (907) 456-BURN (2876) www.kennysburnbarrels.com Incinerators for burning paper, leaves, brush, wood, and debris. Product is made from 55-gallon drums and comes equipped with vents and screen tops. Electric Incinerators Spill Shield Environmental 2000 W. International Airport Road #D2 Anchorage, Alaska 99502 907-561-6033 www.spillshield.com Electrically powered 110-volt incinerator. Innovative combustion system meets EPA air quality emission standards for burning non-hazardous waste. Uses a standard 55-gallon drum. Used in Alaska by DEC, US National Park Service, and the US Army. Forced Air-Diesel Fueled Incinerators Taiga Ventures 2700 S. Cushman Street Fairbanks, Alaska 99701 907-452-6631 www.taigaventures.com Compact, high efficiency, forced air, diesel fueled incinerators manufactured and sized for customer needs. Facebook Twitter Google+ Reddit

Incineration waste examples

Incineration is a great idea for recreational cabin owners, small camp operators, fish camps, or larger work camps. Slow burning fuel and good air flow in a contained fire generate enormous amounts of heat. With proper incineration even wet garbage will burn completely, leaving no food odors. The common 55-gallon drum burn barrels with a few holes are inadequate for incineration. Unless modified substantially, burn barrels do not have adequate air and slow burning fuels and result in scorched and smoldering garbage that attracts bears. Incinerators are generally two types: small, passive air flow incinerators that do not need electricity for fans or fuel pumps, and active flow incinerators that do require power. Passive flow incinerators, such as modified burn barrels (see example below), are more appropriate for recreational cabins or small camps where only one or two bags of garbage are produced a day. For camps producing larger amounts of garbage, active flow incinerators are more appropriate. Some models can be broken down to fit in small aircraft. You can incinerate anything with a food odor--food waste, cooking grease, cans, bottles, gray water residues, and most kitchen garbage. You should not incinerate anything that might explode or cause toxic fumes such s kitchen cleaning powders and sprays, treated lumber, batteries, or aerosol cans. In its "Policy on Human Food and Solid Waste Management and Bears in Alaska" the Alaska Department of Fish and Game states: "The preferred alternative for disposal of garbage that may attract bears is incineration at a facility that meets ADEC standards for combustible residue…Large field camps (more than 15 people) should dispose of garbage by daily incineration in a fuel-fired incinerator that meets ADEC standards…Small permanent facilities (e.g., lodges, weather stations) or large nonpermanent camps (e.g., project fires) should daily segregate and store garbage in a bear-proof container for backhaul to an approved disposal site. Alternatively, (a) putrescible waste and other combustibles could be incinerated in a locally fabricated incinerator meeting ADEC standards for residue." The pamphlet "Open Burning Policy & Guidelines" is available from the Alaska Department of Environmental Conservation, Division of Air Quality Air Permits Program. For Open Burning questions contact: Interior Alaska Kathy Stringham (907) 451-2114 Southcentral Alaska Cynthia Espinoza, (907) 269-7575 Southeast Alaska & Aleutians Jeanette Brena (907) 465-5122 Safety Information Used improperly or in extreme conditions burn barrels and incinerators can cause wildfires! Complete incineration of wet garbage items requires a slow burning fuel, such as diesel or kerosene, or the aid of propane or electricity. Regardless of what you use all incinerators require plenty of air to work properly. Only non-toxic materials should be burned in incinerators. Incinerators in areas accessible to bears should be cleaned at regular intervals, as residues can an attractant. Accumulation of ash can also blocking air flow. Incineration of garbage can leave a temporary odor trail that a bear could follow. Where feasible, the incinerator should be located downwind from the camp or tent area (and inside the electric fence if there is one). Burning should be scheduled during the day or immediately after dinner when people are still awake and active. Directions for building your own incinerator "Yukon Incinerator" A camp producing one full garbage bag a day can use a homebuilt incinerator made from fuel drums. Larger camps can get by with similar homebuilt models, made from culverts, but should look to efficient forced-air, fuel-fired, or electric commercial incinerators. See below for vendors. Before you get started building your own incinerator, you should consider the design carefully: Garbage must get really hot before it will incinerate. The sizes of the vent and chimney are critical to get the airflow required to support a hot fire. If it doesn't burn well, raise the chimney. "Empty" fuel drums need to be steamed or washed out, or filled with water or exhaust before they are cut or welded. If not, residual fuel fumes can cause serious explosions Avoid using gas drums. Most garbage is too wet to burn on its own. To prevent explosions, slow burning fuels like diesel or stove oil, wood or cardboard should be used rather than highly flammable fuels. A lighter torch may be used in the vent to start the fire. Suspending the garbage in a steel mesh basket or by a grill helps dry it out and ensure that the airflow is maintained. A removable basket greatly simplifies ash removal. Size the burn chamber for one bag of garbage. Don't store garbage in your incinerator "until there is enough for a good burn." If you leave wet garbage in the incinerator it will attract bears. IMPORTANT: The Alaska Department of Fish and Game does not guarantee nor warrant the design, effectiveness and/or safety of these devices under any circumstances. Train every incinerator operator in the safe use of the incinerators. Suggestions for building your own incinerator are contained in the attached files. Vendors Small Incinerators Aleckson Fabricators 38735 S. Ruby Circle Soldotna, Alaska 907-262-9654 shirley@alaska.net This incinerator weighs approximately 150 pounds and comes apart into two sections for easy transportation by 4 wheeler, snowmachine, boat, or appropriate aircraft. A demonstration model of this incinerator can be seen at the ADF&G office in Soldotna or in Spring 2004 in the Caribou Hills on the Kenai Peninsula. Aleckson Fabricators also makes bear-resistant containers from aluminum and steel. Kenny's Burn Barrels Manufacturing and Engineering Co. P.O.Box 70476 Fairbanks, AK. 99707 (907) 456-BURN (2876) www.kennysburnbarrels.com Incinerators for burning paper, leaves, brush, wood, and debris. Product is made from 55-gallon drums and comes equipped with vents and screen tops. Electric Incinerators Spill Shield Environmental 2000 W. International Airport Road #D2 Anchorage, Alaska 99502 907-561-6033 www.spillshield.com Electrically powered 110-volt incinerator. Innovative combustion system meets EPA air quality emission standards for burning non-hazardous waste. Uses a standard 55-gallon drum. Used in Alaska by DEC, US National Park Service, and the US Army. Forced Air-Diesel Fueled Incinerators Taiga Ventures 2700 S. Cushman Street Fairbanks, Alaska 99701 907-452-6631 www.taigaventures.com Compact, high efficiency, forced air, diesel fueled incinerators manufactured and sized for customer needs. Facebook Twitter Google+ Reddit

The pamphlet "Open Burning Policy & Guidelines" is available from the Alaska Department of Environmental Conservation, Division of Air Quality Air Permits Program. For Open Burning questions contact: Interior Alaska Kathy Stringham (907) 451-2114 Southcentral Alaska Cynthia Espinoza, (907) 269-7575 Southeast Alaska & Aleutians Jeanette Brena (907) 465-5122

Used improperly or in extreme conditions burn barrels and incinerators can cause wildfires! Complete incineration of wet garbage items requires a slow burning fuel, such as diesel or kerosene, or the aid of propane or electricity. Regardless of what you use all incinerators require plenty of air to work properly. Only non-toxic materials should be burned in incinerators. Incinerators in areas accessible to bears should be cleaned at regular intervals, as residues can an attractant. Accumulation of ash can also blocking air flow. Incineration of garbage can leave a temporary odor trail that a bear could follow. Where feasible, the incinerator should be located downwind from the camp or tent area (and inside the electric fence if there is one). Burning should be scheduled during the day or immediately after dinner when people are still awake and active. Directions for building your own incinerator "Yukon Incinerator" A camp producing one full garbage bag a day can use a homebuilt incinerator made from fuel drums. Larger camps can get by with similar homebuilt models, made from culverts, but should look to efficient forced-air, fuel-fired, or electric commercial incinerators. See below for vendors. Before you get started building your own incinerator, you should consider the design carefully: Garbage must get really hot before it will incinerate. The sizes of the vent and chimney are critical to get the airflow required to support a hot fire. If it doesn't burn well, raise the chimney. "Empty" fuel drums need to be steamed or washed out, or filled with water or exhaust before they are cut or welded. If not, residual fuel fumes can cause serious explosions Avoid using gas drums. Most garbage is too wet to burn on its own. To prevent explosions, slow burning fuels like diesel or stove oil, wood or cardboard should be used rather than highly flammable fuels. A lighter torch may be used in the vent to start the fire. Suspending the garbage in a steel mesh basket or by a grill helps dry it out and ensure that the airflow is maintained. A removable basket greatly simplifies ash removal. Size the burn chamber for one bag of garbage. Don't store garbage in your incinerator "until there is enough for a good burn." If you leave wet garbage in the incinerator it will attract bears. IMPORTANT: The Alaska Department of Fish and Game does not guarantee nor warrant the design, effectiveness and/or safety of these devices under any circumstances. Train every incinerator operator in the safe use of the incinerators. Suggestions for building your own incinerator are contained in the attached files. Vendors Small Incinerators Aleckson Fabricators 38735 S. Ruby Circle Soldotna, Alaska 907-262-9654 shirley@alaska.net This incinerator weighs approximately 150 pounds and comes apart into two sections for easy transportation by 4 wheeler, snowmachine, boat, or appropriate aircraft. A demonstration model of this incinerator can be seen at the ADF&G office in Soldotna or in Spring 2004 in the Caribou Hills on the Kenai Peninsula. Aleckson Fabricators also makes bear-resistant containers from aluminum and steel. Kenny's Burn Barrels Manufacturing and Engineering Co. P.O.Box 70476 Fairbanks, AK. 99707 (907) 456-BURN (2876) www.kennysburnbarrels.com Incinerators for burning paper, leaves, brush, wood, and debris. Product is made from 55-gallon drums and comes equipped with vents and screen tops. Electric Incinerators Spill Shield Environmental 2000 W. International Airport Road #D2 Anchorage, Alaska 99502 907-561-6033 www.spillshield.com Electrically powered 110-volt incinerator. Innovative combustion system meets EPA air quality emission standards for burning non-hazardous waste. Uses a standard 55-gallon drum. Used in Alaska by DEC, US National Park Service, and the US Army. Forced Air-Diesel Fueled Incinerators Taiga Ventures 2700 S. Cushman Street Fairbanks, Alaska 99701 907-452-6631 www.taigaventures.com Compact, high efficiency, forced air, diesel fueled incinerators manufactured and sized for customer needs. Facebook Twitter Google+ Reddit

Length of warranties do vary from 30 days to lifetime. Each warranty only covers failures due to defects or workmanship which occur during normal use. It does not cover failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alternation, modification, or unauthorized use by others.

Incineration

Small Incinerators Aleckson Fabricators 38735 S. Ruby Circle Soldotna, Alaska 907-262-9654 shirley@alaska.net This incinerator weighs approximately 150 pounds and comes apart into two sections for easy transportation by 4 wheeler, snowmachine, boat, or appropriate aircraft. A demonstration model of this incinerator can be seen at the ADF&G office in Soldotna or in Spring 2004 in the Caribou Hills on the Kenai Peninsula. Aleckson Fabricators also makes bear-resistant containers from aluminum and steel.

Only non-toxic materials should be burned in incinerators. Incinerators in areas accessible to bears should be cleaned at regular intervals, as residues can an attractant. Accumulation of ash can also blocking air flow. Incineration of garbage can leave a temporary odor trail that a bear could follow. Where feasible, the incinerator should be located downwind from the camp or tent area (and inside the electric fence if there is one). Burning should be scheduled during the day or immediately after dinner when people are still awake and active. Directions for building your own incinerator "Yukon Incinerator" A camp producing one full garbage bag a day can use a homebuilt incinerator made from fuel drums. Larger camps can get by with similar homebuilt models, made from culverts, but should look to efficient forced-air, fuel-fired, or electric commercial incinerators. See below for vendors. Before you get started building your own incinerator, you should consider the design carefully: Garbage must get really hot before it will incinerate. The sizes of the vent and chimney are critical to get the airflow required to support a hot fire. If it doesn't burn well, raise the chimney. "Empty" fuel drums need to be steamed or washed out, or filled with water or exhaust before they are cut or welded. If not, residual fuel fumes can cause serious explosions Avoid using gas drums. Most garbage is too wet to burn on its own. To prevent explosions, slow burning fuels like diesel or stove oil, wood or cardboard should be used rather than highly flammable fuels. A lighter torch may be used in the vent to start the fire. Suspending the garbage in a steel mesh basket or by a grill helps dry it out and ensure that the airflow is maintained. A removable basket greatly simplifies ash removal. Size the burn chamber for one bag of garbage. Don't store garbage in your incinerator "until there is enough for a good burn." If you leave wet garbage in the incinerator it will attract bears. IMPORTANT: The Alaska Department of Fish and Game does not guarantee nor warrant the design, effectiveness and/or safety of these devices under any circumstances. Train every incinerator operator in the safe use of the incinerators. Suggestions for building your own incinerator are contained in the attached files. Vendors Small Incinerators Aleckson Fabricators 38735 S. Ruby Circle Soldotna, Alaska 907-262-9654 shirley@alaska.net This incinerator weighs approximately 150 pounds and comes apart into two sections for easy transportation by 4 wheeler, snowmachine, boat, or appropriate aircraft. A demonstration model of this incinerator can be seen at the ADF&G office in Soldotna or in Spring 2004 in the Caribou Hills on the Kenai Peninsula. Aleckson Fabricators also makes bear-resistant containers from aluminum and steel. Kenny's Burn Barrels Manufacturing and Engineering Co. P.O.Box 70476 Fairbanks, AK. 99707 (907) 456-BURN (2876) www.kennysburnbarrels.com Incinerators for burning paper, leaves, brush, wood, and debris. Product is made from 55-gallon drums and comes equipped with vents and screen tops. Electric Incinerators Spill Shield Environmental 2000 W. International Airport Road #D2 Anchorage, Alaska 99502 907-561-6033 www.spillshield.com Electrically powered 110-volt incinerator. Innovative combustion system meets EPA air quality emission standards for burning non-hazardous waste. Uses a standard 55-gallon drum. Used in Alaska by DEC, US National Park Service, and the US Army. Forced Air-Diesel Fueled Incinerators Taiga Ventures 2700 S. Cushman Street Fairbanks, Alaska 99701 907-452-6631 www.taigaventures.com Compact, high efficiency, forced air, diesel fueled incinerators manufactured and sized for customer needs. Facebook Twitter Google+ Reddit

"Yukon Incinerator" A camp producing one full garbage bag a day can use a homebuilt incinerator made from fuel drums. Larger camps can get by with similar homebuilt models, made from culverts, but should look to efficient forced-air, fuel-fired, or electric commercial incinerators. See below for vendors.

IMPORTANT: The Alaska Department of Fish and Game does not guarantee nor warrant the design, effectiveness and/or safety of these devices under any circumstances. Train every incinerator operator in the safe use of the incinerators. Suggestions for building your own incinerator are contained in the attached files.

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Garbage incinerators can stop bear problems. Burning in pits or the common "burn barrel" attracts bears. The fuel drains into the dirt or into cans beneath your garbage so that garbage is only scorched. The fire smolders for hours. Bears will dig up half-burned garbage. Fast burning fuels and inadequate air, such as in a pit or a drum result in scorched and smoldering garbage that attracts bears.